Jump to content
SAU Community

Recommended Posts

I found this by pure chance and it has some usual features .

http://www.nzperformance.co.nz/store/garre...r/prod_189.html

I'm not sure which comp wheel this one has but will look around , Brett says that one of them uses the 76.2mm 52 trim GT37 compressor - same as the 3037 52T .

Possibilities in altered form , cheers A .

I found this by pure chance and it has some usual features .

http://www.nzperformance.co.nz/store/garre...r/prod_189.html

I'm not sure which comp wheel this one has but will look around , Brett says that one of them uses the 76.2mm 52 trim GT37 compressor - same as the 3037 52T .

Possibilities in altered form , cheers A .

I'm pretty sure that's just a normal off the shelf item from Garrett.

Very overpriced too. They're at least a few hundred cheaper locally.

Who is Brett?

Have to agree, that looks a little old school and at 500hp rating isn't worth it. Still prefer the 3076 in anti surge configuration. The problem with these things is if nobody has tried it then what if you strap it on and it gives up the ghost at 250kws. Or ends up a laggy 3040 type turbo. That price looks a little high as suggested to, do yourself a favour and go to the ATP turbo site in the States. Got all my stuff there and is cheap. Then again, buy Australian and if you get it all from the one place maybe a discount is in order. As I said in my PM Adrian, just go with the .82 exhaust option and if you try this turbo, who knows, it may work out. I am not into external waste gates but then again as we've discussed the 63 housing with a 50mm waste gate should give you the best of both worlds. Still prefer the bigger housing though.

Brett from GCG I believe.

Edited by skylinecouple

Only relying on memory here...but doesn't the 2876 use a 52 trim 76mm comp wheel/housing - which may be the source of the compressor side of this setup.

Late Edit: Actually no, I just checked and the 2876 uses a 48 trim 76mm comp wheel and .70 comp housing - close but no cigar.

Edited by juggernaut1

No a GT3071R has a GT30 turbine (normal or cropped) with a 71.1mm 56T compressor wheel .

A GT3037S is a HKS marketed GT3076R having a GT30 turbine and a 76.2mm GT compressor , "S" in HKS's case means with the port shrouded compressor housing . The plain inlet snout ones are just called 3037 or GT3037 .

Doesn't matter anyway because that turbo in the above link is the wrong comp wheel style so no good .

Got the spies looking for either the right turbo or at least the right cartridge which appears to be available .

A .

So much choice. Well, look at the bright side, 10 years ago things were mighty different. To3 or To4, take your pick. Hey Adrian, what mods have you got so far ? Your not planning on cams or going for a rebuild are you ?

Just about to call you , hopefully talk this afternoon .

BTW I followed a link from an SR site to a HKS Japan site and this is what they say about their 3037 52T kit for S15 Silvias inc supposed dyno graph .

Now I know an S15 SR20DET is very different from an R33 RB25 and my guess is that an unopened late SR20 would be in a pretty soft state of tune . Can anyone who reads Japanese tell me whats been done to it please .

http://www.hks-power.co.jp/products/turbo/...waste_gtsp.html

Cheers A .

Funny you found this, I have been speaking with a reputable garrett turbo wholesaler in South Aus and was talking about the Garrett GT3076R.

They have 2 types that they sell, one is the GT3076R with anti surge compressor housing and .82 ext gate rear housing to suit, Trim is something like - 57 comp wheel, 55 turbine wheel.

The other is pretty much the same turbo with the 4" bell mouth compressor housing like the GT30R, with .82 ext rear housing - trim is 54.97 comp wheel, 53 rear turbine wheel.

Priced fairly differently, would there be an issue going with the GT3076R without the anti surge housing? all supporting mods looking for around 270-280rwkw.

Do a search, but I remember reading somewhere that some [note not all] users were experiencing surge.

I have the 100mm port shroud 'with all the supporting mods' and have not had any issues, but it depends on too many things to say that this will or will not happen.

Defining 'all supporting mods' is a key issue.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
×
×
  • Create New...