Jump to content
SAU Community

R32 Obd Protocol

blinko
 Share

Recommended Posts

blinko Proficient

blinko

Posted
Posted

Im trying to find out what protocol an R32 gts-t OBD would use? does anyone know, or know where i can find out?

Also can anyone tell me what information is available from the OBD, or any good sites where i can find this information in detail?

I need this info for an engineering project i am currently building.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/281363-r32-obd-protocol/
Share on other sites
REDGTT Grand Master

REDGTT

Posted
Posted

Signal protocols

There are five signalling protocols currently in use with the OBD-II interface. Any given vehicle will likely only implement one of the protocols. Often it is possible to make an educated guess about the protocol in use based on which pins are present on the J1962 connector:

* SAE J1850 PWM (pulse-width modulation - 41.6 kbaud, standard of the Ford Motor Company)

o pin 2: Bus+

o pin 10: Bus–

o High voltage is +5 V

o Message length is restricted to 12 bytes, including CRC

o Employs a multi-master arbitration scheme called 'Carrier Sense Multiple Access with Non-Destructive Arbitration' (CSMA/NDA)

* SAE J1850 VPW (variable pulse width - 10.4/41.6 kbaud, standard of General Motors)

o pin 2: Bus+

o Bus idles low

o High voltage is +7 V

o Decision point is +3.5 V

o Message length is restricted to 12 bytes, including CRC

o Employs CSMA/NDA

* ISO 9141-2. This protocol has a data rate of 10.4 kbaud, and is similar to RS-232. ISO 9141-2 is primarily used in Chrysler, European, and Asian vehicles.

o pin 7: K-line

o pin 15: L-line (optional)

o UART signaling (though not RS-232 voltage levels)

o K-line idles high

o High voltage is Vbatt

o Message length is restricted to 12 bytes, including CRC

* ISO 14230 KWP2000 (Keyword Protocol 2000)

o pin 7: K-line

o pin 15: L-line (optional)

o Physical layer identical to ISO 9141-2

o Data rate 1.2 to 10.4 kbaud

o Message may contain up to 255 bytes in the data field

* ISO 15764 CAN (250 kbit/s or 500 kbit/s). The CAN protocol is a popular standard outside of the US automotive industry and is making significant in-roads into the OBD-II market share. By 2008, all vehicles sold in the US will be required to implement CAN, thus eliminating the ambiguity of the existing five signalling protocols.

o pin 6: CAN High

o pin 14: CAN Low

blinko Proficient

blinko

Posted
  • Author
Posted
Signal protocols

There are five signalling protocols currently in use with the OBD-II interface. Any given vehicle will likely only implement one of the protocols. Often it is possible to make an educated guess about the protocol in use based on which pins are present on the J1962 connector:

* SAE J1850 PWM (pulse-width modulation - 41.6 kbaud, standard of the Ford Motor Company)

o pin 2: Bus+

o pin 10: Bus–

o High voltage is +5 V

o Message length is restricted to 12 bytes, including CRC

o Employs a multi-master arbitration scheme called 'Carrier Sense Multiple Access with Non-Destructive Arbitration' (CSMA/NDA)

* SAE J1850 VPW (variable pulse width - 10.4/41.6 kbaud, standard of General Motors)

o pin 2: Bus+

o Bus idles low

o High voltage is +7 V

o Decision point is +3.5 V

o Message length is restricted to 12 bytes, including CRC

o Employs CSMA/NDA

* ISO 9141-2. This protocol has a data rate of 10.4 kbaud, and is similar to RS-232. ISO 9141-2 is primarily used in Chrysler, European, and Asian vehicles.

o pin 7: K-line

o pin 15: L-line (optional)

o UART signaling (though not RS-232 voltage levels)

o K-line idles high

o High voltage is Vbatt

o Message length is restricted to 12 bytes, including CRC

* ISO 14230 KWP2000 (Keyword Protocol 2000)

o pin 7: K-line

o pin 15: L-line (optional)

o Physical layer identical to ISO 9141-2

o Data rate 1.2 to 10.4 kbaud

o Message may contain up to 255 bytes in the data field

* ISO 15764 CAN (250 kbit/s or 500 kbit/s). The CAN protocol is a popular standard outside of the US automotive industry and is making significant in-roads into the OBD-II market share. By 2008, all vehicles sold in the US will be required to implement CAN, thus eliminating the ambiguity of the existing five signalling protocols.

o pin 6: CAN High

o pin 14: CAN Low

thanks for the infor, R32's are OBDI Correct?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Marek
      Hi everyone.

      By Marek · Posted

      Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • DanMac34
      R34 Speedo not working after manual swap

      By DanMac34 · Posted

      Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • joshuaho96
      Speed Sensor replacement

      By joshuaho96 · Posted

      Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • QB6SAGR
      Tein Circuit Master- rebuild worth it?

      By QB6SAGR · Posted

      Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
×
×
  • Create New...