Jump to content
SAU Community

Recommended Posts

it only kicks in around 80kph as Aaron has said. its basically an electronic actuator (motor) that controls a steering rack attached to the back of the rear subframe and is liked to the rear of the wheel hub with a toe arm. on the R32 & S13 models it was a hydraulic setup driven off the power steering pump. it turns the rear wheels only by approx 0.7 deg from center, so if your where going around a right hand bend you wheels would be something like this:

front wheels // //

rear wheels \\ \\

when you install a HICAS lock bar you remove the actuator/rack and put a solid bar in between the two toe arms to hold the rear wheel toe where you want it.

edit: beat me with a much better diagram MIKE lol

Edited by QWK32
Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4753292
Share on other sites

HICAS is a very complex system, that is way over what most people think it is.

It helps to make a car feel shorter & more nimble, and helps to damp Yaw effect.

A long wheelbase car is easier to control but slower to turn. Rear wheel steering helps to turn the vehicle.

It has been heavily critisized for making the rear end feel loose, vauge and unnatural.

Lots of HICAS systems get taken off cars, mostly because owners do not fully understand what it is about.

It is there to make the car drive faster.

As you enter the corner the rear of the car actually gets kicked out, which reduces understeer, if you stay hard on the accelerator, as the car reaches the apex, the steering, G-sensors and throttle position will let the car "know" that it is at the apex, the rear wheels will come into phase and the car will steer straight though the apex, to take the fastest line through the corner.

It's kinda like taking a drifters line without drifting.

Your car should have the same system as the R34, which is also a model following control system.

It is pre-programmed to follow cornering models. It is not just feedback based.

If you really want to find out more about, and get a new admiration for our favorite car (sorry not the Stagea) get the book Nissan GTR by Alex Gorodji. Some of the above is taken from the book.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4753764
Share on other sites

simple diagram

how_hicas_works.gif

i really hope it doesnt work that way, thats very dangerous!! if the rear wheels are turning in the same direction as the front wheels, instead of the opposite, then u r in big trouble if the front doesnt turn in. in an understeer situation, that would have the rear wheels turning u straight off the road!!

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4753813
Share on other sites

HICAS is a very complex system, that is way over what most people think it is.

It helps to make a car feel shorter & more nimble, and helps to damp Yaw effect.

A long wheelbase car is easier to control but slower to turn. Rear wheel steering helps to turn the vehicle.

It has been heavily critisized for making the rear end feel loose, vauge and unnatural.

Lots of HICAS systems get taken off cars, mostly because owners do not fully understand what it is about.

It is there to make the car drive faster.

As you enter the corner the rear of the car actually gets kicked out, which reduces understeer, if you stay hard on the accelerator, as the car reaches the apex, the steering, G-sensors and throttle position will let the car "know" that it is at the apex, the rear wheels will come into phase and the car will steer straight though the apex, to take the fastest line through the corner.

It's kinda like taking a drifters line without drifting.

Your car should have the same system as the R34, which is also a model following control system.

It is pre-programmed to follow cornering models. It is not just feedback based.

If you really want to find out more about, and get a new admiration for our favorite car (sorry not the Stagea) get the book Nissan GTR by Alex Gorodji. Some of the above is taken from the book.

i would have to agree, i had a loaner R33 sedan with hicas, and for a big heavy car, this thing handled quite well and could be easily thrown around. i have no idea why people complain about hicas so much. i think they hear that one person doesnt like it and calls it useless, then it MUST be. if it WAS useless, car manufacturers wouldnt be equipping cars with it.......

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4754142
Share on other sites

I think the biggest complaints about HICAS come from anyone who has a dedicated track/drift car, or frequents a track for racing or drifting. And because every second person thinks of themselves as a race car driver or drifter they remove it based on what the real race driver and drifters have said.

Personally I liked the HICAS on my old 32 but can vouch for the fact that once the tail end is out there, it's too easy to over correct because the HICAS system is also assisting the turn.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4754451
Share on other sites

You have to love the original HICAS implementation in the R31's - it had a couple of rams and flexed the entire K-frame on it's bushes!

4WS seems to have dropped off the radar these days, possibly due to it's mechanical complexity vs. what you can to with ESP and it's broader safety benefits.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4754683
Share on other sites

i really hope it doesnt work that way, thats very dangerous!! if the rear wheels are turning in the same direction as the front wheels, instead of the opposite, then u r in big trouble if the front doesnt turn in. in an understeer situation, that would have the rear wheels turning u straight off the road!!

open your eyes before your mouth please

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4755401
Share on other sites

i really enjoy hicas . and really notice when it comes on . eg same piece of road at different speeds . also mint for turning on hicas test and your car sits there and every 2 seconds the rear wheels move full lock (1 degree ish) one way and then other way then back to normal as fast as they can . and every one says wtf is your car doing ? "its break dancing "

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4755416
Share on other sites

Has anyone ever had HICAS work in a straight line? That sort of issue, giving the car a 'flick'? Possibly due to the wheel not being on straight...?

only when the speedo cable snapped when i was on my way home from work, hicas started playing up along with the usual heavy steering. i was crab walking up a straight road, very strange feeling.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4755455
Share on other sites

only when the speedo cable snapped when i was on my way home from work, hicas started playing up along with the usual heavy steering. i was crab walking up a straight road, very strange feeling.

That's exactly what I had but without the heavy steering. :) Definite crab walk. Happens at higher speeds like 80km/h and you need to steer into it and if slow down quick a flick out of it. I recently had work done on the suspension but the steering wheel is not that straight after the alignment and wondered if that had anything to do with it...? Speedo cable is all good.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/#findComment-4755483
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...