Jump to content
SAU Community

Recommended Posts

Hey guys just wondering should i be worried around 3 months ago i installed a koyo radiator with stock standard radiator cap the temp on my pfc showed 79-80 degrees when warmed up but 3 months ago i installed a ARC radiator cap and the temp never raises past 65 degrees its even lucky to see 65 degrees so im just wondering should i revert to my standard radiator cap? or just leave it? im not loosing any coolant

Cheers

Chi

Link to comment
https://www.sau.com.au/forums/topic/282672-water-temp/
Share on other sites

did it only go up to 65 degrees from the moment you put it on? or has it only just started staying that low? if it has only justed then it will probably be your thermostat. if it started that the moment you put the new cap on the put the old one back on.

Link to comment
https://www.sau.com.au/forums/topic/282672-water-temp/#findComment-4759667
Share on other sites

Aftermarket caps on a stock rad are a very bad idea.

The problem is most aftermarket caps have a much higher point of pressure.

This means if you do actually overheat the cap wont pop off when it should, and what will happen is the radiator header tank which is plastic - will simply blow apart and send bits flying everywhere at a very much higher pressure than was ever intended

I remember this happening when i was in Pete's (bass junky) car, and it put a good 2-3 solid dints into the bonnet which is some rather nasty damage and quite costly to fix for just changing a cap.

Since that day i will never change from a factory rated cap (or replacement) on a radiator that is not full alloy.

Link to comment
https://www.sau.com.au/forums/topic/282672-water-temp/#findComment-4760371
Share on other sites

thanks for the reply R31nismoid but the radiator is a KOYO aftermarket one ahh well tonight i put the stock cap back on and max temp was like 65 so im guessing its the thermostat could it be ne thing else? guess its a good time to upgrade to gates radiator hoses + nismo thermostat

Link to comment
https://www.sau.com.au/forums/topic/282672-water-temp/#findComment-4760734
Share on other sites

mine sits on 84 at the moment but its leaking coolant via the water pump which will soon be replaced.

I have a fully sick Spac rad cap which has a nipple attached to a hose running down the engine bay and a nifty button to release pressure before opening. Yeah I know you're jealous of it :P

Link to comment
https://www.sau.com.au/forums/topic/282672-water-temp/#findComment-4760751
Share on other sites

The r32 gtr i just bought sits on about 79-80 degs just like yours once its warmed up, mine runs a blitz radiator cap and im not to sure but i dont think its the factory radiator is this a good temp it should be running at?

Link to comment
https://www.sau.com.au/forums/topic/282672-water-temp/#findComment-4760853
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...