Jump to content
SAU Community

Recommended Posts

hey guys i am basiclly a first time writer but long time onliner if you get my flow.....

im in the market for a r32gtr and tonite i went and had a look at one, now ive been searching for a while and the one that i took a look at is fairly standard and looks pritty legite.......

what do u guys think????? "i took my skyline manual with me and it pritty well checks off every thing in the list?

http://www.carsales.com.au/all-cars/privat...id=1223C82ACD25

one thing, he claimed it makes 239 kws at the rears with the 4wd disingaged cause of the fact he was on a two wheel dyno but is still runing standard boost wat do u think modds are as followed on the link

also the frount mount didnt look standard

cheers in advance

giuseppe

Edited by r32gtr92
Link to comment
https://www.sau.com.au/forums/topic/282789-my-first-skyline/
Share on other sites

I think he's pulling himself with 238kw with very little power mods. Well, unless he can prove it.

Yeah +1.

Ask him for a Dyno sheet print out.

Seller says:

"Engine is mechanically sound and exterior is in great condition. Very clean and neat car that gets driven a maximum of twice a week.

Extras:

Stainless steel 3" Greddy catback exhaust,

Exceedy heavy duty clutch,

Pod filters,

Alpine stereo speakers

7" Motorised LCD DVD/VCD/TV Player (USB and SD card compatible),

Remapped ECU

Turbo Timer.

All resonable offers will be considered"

Car looks pretty stock to me... Cat back exhaust, twin pod filters and a Remapped ECU = 239 Rear Wheel kW's..?

Don't think so.

Ask him what has he done to the ECU, stock or aftermarket?

Remapping an ECU means fine tuning the the Unit to get better performance out of your car by altering the Air/Fuel Ratios, settings...

In doing so to try and increase power and torque and making the car more responsive down low, mid range or top end and try to cancel out any flat spots in the power and torque curves.

After doing so I still can't see how he got 239 rw kW's unless having Dyno sheet to prove.

cheers 00skyline00 ,

thats what i thought took it for a test drive and it felt pritty quick compared to stockers that ive been in but like you said i dont think its possible either,

great responsiveness i must say?

gonna call for a dyno sheet for proof.

wopps didnt relise i was loged in to my lost acount that i didnt think was there any more,

as above

all comments are welcome>?

Yeah no worries!

But still take another look into the car, if it runs well and a tad quicker then standard, in a good condition...

Do a bit more research, ask a few more questions and even take you mechanic down with you next time to see the car.

The seller is negotiable on price so take a stab at it... He wants $18,499, then see if he will take anything in the $16K range.

If not then you both meet each other half way on the price, say $17,500 or whatever...

If he won't lower the price, meaning he still thinks his car has some good mods and can make 239kW's. (Trying to get some money back on the "Mods" he has done")

If he is willing to lower it then you know it's pretty much stock...

My point of view anyway and this is all in speculation, cuz I am not standing in front of the car and just judging from the Carsales add.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...