Jump to content
SAU Community

Recommended Posts

Hey all just wondering if a Q45 throttle body will work on a RB25 with a greddy plenum and a stock ecu? (i've already wired up tps etc) Will it effect fuel maps on high load dude to the greater flow of air? or will it last one night of skidding at QR?

any advise would help heaps cheers Davo.

Link to comment
https://www.sau.com.au/forums/topic/284562-q45-tb-stock-ecu/
Share on other sites

Aftermarket plenum with stock ECU?? WTF?

If the TB makes a difference to the flowrate (ie if its less or more restrictive than what you have now) you might get into different cells in the fuel maps, but being a stock ECU everything will be very conservative so i doubt you'll notice any difference.

Changing injector size or MAF is what doesnt work with stock ECU.

Aftermarket plenum with stock ECU?? WTF?

If the TB makes a difference to the flowrate (ie if its less or more restrictive than what you have now) you might get into different cells in the fuel maps, but being a stock ECU everything will be very conservative so i doubt you'll notice any difference.

Hehe... Pretty much my reaction as well.

To the OP - Why do you need a Q45?

All you do is soften the accelerator control/response by going a bigger TB. It is 110% NOT required.

I ran near on 400rwkw with the stock TB without a problem as have plenty of people before/after myself.

TB Upgrades for the most part are silly. I actually know of two people who have taken them off and gone back to the factor one for more precise throttle control.

The reason i used a Q45 TB is becasue i dont have enough time to make a adaptor plate and it bolts stright up to a greddy plenum. I'll be chucking in a PFC within 2 weeks but the reason i ask if a stock ecu will work is because i plan on taking my car on track without engine failure. The Q45 is a massive TB and i just thought it would b easyer chucking it on whilst i did my inlet manifold but there isnt really a need for it. but thanks everyone for ya input i'll let u know how it skids when i finish my cooler piping.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...