Jump to content
SAU Community

Recommended Posts

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

Stock turbo on a "happy" dyno then yes, possible. In reality it's more like 270-280hp.

I maxed the exhaust side of my 25 turbo with only 250rwhp, more left in the compressor but the exhaust housing just couldn't flow enough.

Edited by bubba
Link to comment
https://www.sau.com.au/forums/topic/286187-r33-300rwhp/#findComment-4802840
Share on other sites

so ansure is yes around about 300hp

That's pretty much the absolute maximum, and yes each dyno is slightly different, but I've seen it on a couple cars. Most will achieve 260-280rwhp max, cause most people don't want to destroy there engine/turbo by what is require to get to 300rwhp :)

Link to comment
https://www.sau.com.au/forums/topic/286187-r33-300rwhp/#findComment-4802871
Share on other sites

having a heated discution with a mate.. would like to get your opinion..

on a r33 rb25det

can you get 300rwhp?

i say yes...

full turbo back system

front mount intercooler

intake

aftermarket piggy back ecu

boost controler...

what do you think..... ?

No with those mods you listed, yes with other mods such as intake plenum, injector cam upgrades etc.

Edited by Dani Boi
Link to comment
https://www.sau.com.au/forums/topic/286187-r33-300rwhp/#findComment-4803384
Share on other sites

1/4 mile times are not a good measure of power at all!!!

Theres like way too many factors come into account...

Just by changing tyres / pressure results in lower times...

Dynos are just a BENCHMARK to Measure the cars power output 'not performance'.

Link to comment
https://www.sau.com.au/forums/topic/286187-r33-300rwhp/#findComment-4803435
Share on other sites

Well I got 292.9rwhp on stock turbo, so close enough is good enough. Tell your mate that.

I'm sure if you check the rb25 dyno results thread you will find some stock turbo readouts around the 300rwhp figure.

Edited by SKYRYAN
Link to comment
https://www.sau.com.au/forums/topic/286187-r33-300rwhp/#findComment-4803446
Share on other sites

be careful with e85.. will eat ur stock fuel pump setup if ur not careful and get a proper setup :D

im aiming for atleast 350rwhp

not in stock though :D i'll be buying parts over the course of time and have them installed at once hehe (have a powerfc sitting in my room waiting to be installed once i get ebc and finish exhaust ^_^)

Link to comment
https://www.sau.com.au/forums/topic/286187-r33-300rwhp/#findComment-4803486
Share on other sites

who cares about the power figure you run on a dyno...

it's about how drivable the car is and how well you can drive it, s**t if i gave my dad 500hp to my 250 i would still whoop his arse...

decide what you want and tell your mate that power figures are for tools in V8's without a penis :D

Link to comment
https://www.sau.com.au/forums/topic/286187-r33-300rwhp/#findComment-4803861
Share on other sites

why is e85 even been mentioned in this thread when it isnt available in WA?

Because the question is "CAN YOU GET 300RWHP WITH STOCK TURBO?"

There is no mention of WA resources only!

Besides i am sure you could get E85 sent over.

Link to comment
https://www.sau.com.au/forums/topic/286187-r33-300rwhp/#findComment-4803923
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...