Jump to content
SAU Community

Recommended Posts

Hi there,

I know its not a skyline, but, I've been a member on this forum since when I owned my '32 GTR, and I value what knowledge there is on this forum - so maybe you guys can help me out on this one :ph34r:

I was driving my MR-2 today and noticed the Ext.Temp gauge rocket up to in excess of 1000 degrees celsius - well into the red zone on the gauge.

Knowing that high ext temps can often mean serious detonation, I drove it carefully out of boost the whole way home (I'd been driving it like a nanna all day - 50km/h road limits here in Japan!).

I switched it off to eat dinner. Came back out after 90 minutes, and it rocketed back up to 1100 degrees within minutes of starting it up again.

Couple things confuse me though - the reading went from the low part of the gauge to the upper part of the gauge within minutes of driving. Nothing gradual from the looks of things, although I wasn't staring at the gauge the whole time. I looked back after 2-3 mins and it was back in the red (after starting the car at the low end of the gauge).

I wasn't driving it hard at all (all below 4k rpm, well out of boost), and the car was behaving normally as it always does. No other signs of untoward worry - fuel pressure was fine, as was oil/water temp, no smoke, no pinging, nothing.

The car is running a Trust TD-06, aftermarket cams, AVCD and an Apexi Power FC among many other things.

Any ideas? Have I got a faulty gauge? Or is there something possibly terminal lurking under the hood that I should be worried about?

If you are indeed seeing temps of 1000c+ for more than a second or two, a lot of things should be glowing orange/red under the hood like the exhaust housing of the turbo for one. Is the temp fluctuating with throttle input? What is the temp at idle?

The gauge is a GReddy gauge and reads on a scale of 4 - 12. Each being x 100 degrees celsius.

It was sitting at between 11 and 12 on the gauge. Not fluctuating at all with idle or throttle input. Dead steady as a matter of fact.

Oil and water temp also completely unchanged.

I reckon you got a guage problem for sure, or the pickup is faulty.Have you had a look under the hood when the guage is reading so high ? Anything look glowing orange ? Is the heat coming out seem excessive compared to previously?

Car has no cat. I'd say if it was a blocked cat, there'd be power issues as well due to the restriction in the exhaust.

The wiring is unbroken, but does look a little old.

Drove it today, and the gauge again was showing a high temp, but would often drop back down. Considering there seemed to be no correlation between idle, throttle on/off and the reading on the gauge, I'm %90 sure its a faulty signal.

When it wasn't peaking off the dial, it read around the 550 degrees celsius mark which is close to the bottom of the gauge. No A/F meter handy so I can't say for sure though... Will definitely get it sussed out properly - not worth taking a risk and ending up with a dead motor :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...