Jump to content
SAU Community

Recommended Posts

Just finished Brembo conversion on my car

documented some details and so on.

and took alot of pics

Picture057.jpg

Brembos Finally arrived

Picture058-1.jpg

Closer look at the front.

Picture059-1.jpg

With the Rest of my stuff

Slotted EBC rotors and EBC red stuff brake pads

Picture061.jpg

Standard Front

Picture062.jpg

Standard rotor vs new 324mm rotors

Picture064.jpg

Fronts installed

The fronts where pretty easy and straight forwards but you must use the brake lines off the 350gt as it will be a straight fit

using the brackets

The rears needed abit of modification on the dust cover and the brake lines needed some custom mountings

Picture069.jpg

dust covers designed for the standard rotors

Picture070.jpg

Had to get a nibbler and modify it

Picture068.jpg

Rear brembos installed

*the standard caliper blots coudlnt be used cuz it had a finer thread u can either use OEM Z33 or aftermarket caliper bolts

Link to comment
https://www.sau.com.au/forums/topic/288150-m35-brembo-brake-coversion/
Share on other sites

So stolked to see that Danny! Its exactly what I have been planning.

Can you give me the part numbers for the rotors you used. Also did you need to to make a mounting adaptor for the rear calipers, or just make room with the dust tins?

Ben.

i can provide you all the part numbers

but only mod to the rear was the dust pan and different bolts

no mods were requiered to fit the rear

price wise would set u back 2.5K-3K

obviously i didnt pay that much for it lol

going to finish off blddeding the brakes today

so ill let u guys know how it feels

is there a chance youll have to upgrade your master cylinder?? else youll be pushing VERY far on the pedal before it grabs. might need to get the master from a brembo equipped V35 (if they are different)

too much movement..

it's not hard enuff for brembos

A larger piston master cylinder will help but if your pedal isnt too low, see how it goes.

Have you bed the brakes in properly? Go for a thrash through the mountains and they will feel better after, promise. If not, you might just need to re-bleed.

I was hoping for a better review of the EBC reds... :thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well, yes, every CU on the bus is available via the Consult port, but whether the scanner you are using is capable of talking to the TCU, the ABS/TCS modules, etc etc, is what is at question here. Many of them are only for engine codes. So, if you have one of those, you won't know if the ABS is having a bitch.
    • That's now. R chassis Skylines come from a time when the tolerance in the ADRs was a bit more....slack. My car, on 235/35-17, which is damn near the exact same size as the original 205/55-16, is pretty much bang on correct indicated speed across the whole legal range. That's demonstrated with constant speed run over 5km, and GPS speed. It's just the luck of the draw. My particular speedo head has to be the thing that is "calibrated" that way, because everything else (the diff ratio, the gearbox and the speedo drive**) are all same same as most other Skylines. **OK, so the speedo drive is a Navara unit to drive the R32's cable, not the electronic unit than an R33/4 would normally have with teh same gear on it. Otherwise, I applaud your OCD tendencies, and I would do the same if I needed to.
    • Not too sure, I believe the Nissan consult port does everything? Also just filled up the reservoir to full and the light is still on. The float seems to move up and down fine.
    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph on 255/40 17, so again conservative Google says manufacturers need to set the speedo from 4 to 10% slower than actual road speed.....for safety.....and compliance  After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
×
×
  • Create New...