Jump to content
SAU Community

Recommended Posts

update

Gtr blitz BOV Bolt on you get all the pipes $250

R32 gtr rear seats I have two sets$100 each

R31 house FRP flares (front and rear) $600

r32 dash $100 bux

Centre consol $50

Stock gtr blow off valves $150

R32 gts rims Good rubber Just a pair $100

R31 15 inch rims $30

R32 gtr fuel tank + fuel pump $250

R32 GTR diff $450

R32 gtr wiring loom $250

R32 k sport coilovers $700( almost new) sold

R32 gtr door trims $50 each

R32 gtr boot SOLD

R32 gtr doors with glas $200 each

S13 driver side door with glass ect $50

32 gtr rear cradle $100

update

Gtr blitz BOV Bolt on you get all the pipes $250

R32 gtr rear seats I have two sets$100 each

R31 house FRP flares (front and rear) $600

r32 dash $100 bux

Centre consol $50

Stock gtr blow off valves $150

R32 gts rims Good rubber Just a pair $100

R31 15 inch rims $30

R32 gtr fuel tank + fuel pump $250

R32 GTR diff $450

R32 gtr wiring loom $250

R32 k sport coilovers $700( almost new)

R32 gtr door trims $50 each

R32 gtr boot SOLD

R32 gtr doors with glas $200 each

S13 driver side door with glass ect $50

32 gtr rear cradle $100

hey buddy, ill take the r32 wheels and the two door trims. can i pick up this weekend?

regards

Hey fatz do you have the two plastic vent things on the rear parcel shelf? getting a new shelf made up and need the vents :-)

Also after stock front 32 GTR brake set up - callipers, rotors, lines fittings etc pads not too important.

Hey fatz do you have the two plastic vent things on the rear parcel shelf? getting a new shelf made up and need the vents :-)

Also after stock front 32 GTR brake set up - callipers, rotors, lines fittings etc pads not too important.

yea have all of teh above just give me a bell

0448468884

Gtr blitz BOV

Bolt on you get all the pipes

$250

PA020001.jpg

R32 gtr rear seats

I have two sets

$100 each

PA020002.jpg

R31 house FRP flares (front and rear)

$600

Comes with a nice r31 house box

PA020004.jpg

PA020005.jpg

r32 dash

$100 bux

Centre consol $50

PA020006.jpg

Stock gtr blow off valves

$150

PA020007.jpg

R32 gts rims

Good rubber

Just a pair $100

PA020008.jpg

R31 15 inch rims

$30

PA020009.jpg

R32 gtr fuel tank + fuel pump $250

PA020011.jpg

R32 GTR diff $450

PA020012.jpg

R32 gtr wiring loom

$250

PA020013.jpg

R32 k sport coilovers $700( almost new)

PA020014.jpg

R32 gtr door trims $50 each

R32 gtr boot $100

R32 gtr doors with glas $200 each

PA020016.jpg

S13 driver side door with glass ect

$50

32 gtr rear cradle $100

PA020015.jpg

Hey you still got the original rims?

Thanks Nath

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...