Jump to content
SAU Community

Recommended Posts

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

quite possibly :stupid:

nice

sell off all you dont need, grab 2ndhand what you do need, and go for it

my 6700 r32 sedan rb26 has been reduced by around 1200 in parts sales

then added 3500 back into it to get it up to track-standard.

then less 5500 for bike sale. fun project

today i installed the braided front brake lines, front slotted rotors, and qfm a1rm track pads all round

hoping tomorrow my ju-36's arrive

here is the list from my car:

1993 Nissan Skyline GTs-T Rwd 4door grey sedan4 - $6700

RB30 5speed manual rebuilt gearbox with single button clutch

GTR RB26DETT engine with new rebuilt turbos

5Zigen 3" turbo back exhaust

Turbotech manual boost controller - $35

GTR intank fuel pump

Walbro 305LPH external fuel pump - $165

4 litre alloy fuel surge tank with 5m braided fuel lines - $265

550cc Siemens Injectors with new O-rings & seals - $350

Iridium spark plugs 0.75mm gap - $50

Yellow Jacket coil packs - $150

600x400x100mm fmic kit

Drift pod air filters

Oil filter relocation kit - $110

Oil cooler finned cylinder kit - $90

Ryco oil & fuel filter

Castrol Edge 6L oil

Fujimoto oil drain valve - $35

BHP roll cage - $5

Tomei 300kph GTS dash

AEM wideband kit - $250

Autometre boost gauge

Saas gear knob - $30

Saas steering wheel & boss kit - $170

Bride seat rail - $165

Gephardo race seat & 5-point harness - $200

Nismo ecu remap - $30

Map-ECU piggyback to stock ecu - $200

Car alarm - $35

Hood scoops - $25

GTR rear wing - $25

Tein suspension

Greddy strut tower brace & strut boot brace - $100

Nismo front tension rod link set

Slotted front disc rotors

Braided front brake lines - $80

QFM A1RM 780degree track brake pads - $235

17inch RJR Grafic mags

235/45/17 Khumo KU36 semi-slick tyres - $750

anything not listed means it was already on the car

i'll work it out and send u a pm mate

Awesome, gives me time to save up for a clutch etc.

Speaking of Clutches, i have made a choice of 3;

Xtreme Heavy Duty Clutch Kit $800

NPC 10" Heavy Duty Copper Mix Organic Kit $1093.50

ORC 409D-01N Kit $1399

What do people here suggest, or think?

NPC that will rate about 350 rwkw and its a great clutch

should be ceramic though ?? or did you ask for organic

also 10" is a pull type clutch do you have a pull type

I asked for a 95% street, 5% track type of clutch, and i drive an R33 GTST, so my guess is pull type. They say the clutch is good for 300rwkw and retains the factory feel.

i would get a ceramic Abe and just because its a R33 i wouldnt guess its pull most RB25 boxes are push but the GTR's have pull

your's being 1997 might be pull so don't know see if you can get it down to boostworx or another reputable workshop and get them to check it out

ive heard a lot of people praise and bag Jim Berry

they prolly say 300kw because its ceramic when i did the group buys the ceramic push clutches were 350kw and i sold them into 2x R33's this is why i say better check if its push or pull

push is a bit cheaper there push type Ceramic cushioned with 1200kg pressure plate rated for 350kw used to be about $656 << going from memory 2 years ago

see a lot of info in >>This Thread<<

note all links that say click are dead due to there website being upgraded

Abe - Jim Berry: Race Cluth, leave yourself a good hour and give him a call =) worth if for the info alone

Does he have email? I prefer to have things written down so i can reread and refer back to it.

Does he have email? I prefer to have things written down so i can reread and refer back to it.

a while ago they invented these things called pens and paper... some people find them useful, apparently jim is one of these people =P

just my hot tip, dont go for a soild centre cluth!!! :P

a while ago they invented these things called pens and paper... some people find them useful, apparently jim is one of these people =P

f**k luke, you can be a smart arsed flamin mongrel sometimes hey?

dont know if its just me, or my general tolerance being a bit lower of late, but that didnt seem to be a necessary comment to make. same as the mystery that you were trying to elude to in the domestic vs import dyno day thread.

grow up man, seriously

/rant

f**k luke, you can be a smart arsed flamin mongrel sometimes hey?

dont know if its just me, or my general tolerance being a bit lower of late, but that didnt seem to be a necessary comment to make. same as the mystery that you were trying to elude to in the domestic vs import dyno day thread.

grow up man, seriously

/rant

wtf is your problem?

english too dificult for you to understand??

i told him that jim doesnt use e-mail? how is that unnecessary??

and the mystery in the dyno day thread was a broken dyno!!! i don't exactally want to say "bosstworx dyno is broken, so dont go there"

think the only person here that needs to grow up is you!

f**k luke, you can be a smart arsed flamin mongrel sometimes hey?

dont know if its just me, or my general tolerance being a bit lower of late, but that didnt seem to be a necessary comment to make. same as the mystery that you were trying to elude to in the domestic vs import dyno day thread.

grow up man, seriously

/rant

Its not just you!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Biggest thing is you're okay!   It sounds like between the accident, and the drive home, it was a pretty torturous trip again! On the bright side, you took the opportunity to enjoy the event more from the perspective of a spectator, than as an entrant!   Sad to see so much damage to the car. It really has taken a HUGE hit in the front end. If/when you choose to repair, hopefully the rails are straight (At least from shock tower backwards). Hopefully the extra cage coming through there has save most of the chassis rails, and HOPEFULLY saved the motor too. Best of luck when you eventually get motivated to start pulling it down to check it all out
    • Sounds more like what Brad said, that it's mainly transfer. What pad bed in procedure did you use, and did you replace/machine the rotors, or just swap pads?
    • The stutter is almost entirely in the pedal. I don't feel the brakes release and reapply as you would with ABS engaging but the pedal feels that way, without the brakes releasing. It only lasts for less than a second and the pedal is fine again. It's hard to explain, sorry.  I'll get under this weekend and just double check everything is tight. Fluid is at max where I left it.
    • What bedding in procedure did you use?   When you say stutter, what exactly do you mean? Like it feels like someone letting go of the brakes momentarily and regrabbing them again to get you to stop? Re-reading your post, and that is what it kind of makes me think you're explaining, like theres a little bit of a jolt, likely just as you're reaching a stop. I've only had this issue once. And if its caused by what caused mine, you will want to get the car up on stands again and check it over. Mine was a case of a caliper mounting bolt coming out and letting the caliper rotate on the other remaining bolt and gave play in a wheel as it came to a stop. But not every stop either!
    • Yeop... binned it   This will be a summary will not many pics atm and cbf  Fixed the samsonas - it was totally munched Put a new precision 7675 T4 on with proper split pulse mani Got to Sydney to get to car - drove to canberra to get racecar - drive back to sydney that night Next day all day at Plasmaman putting on new clamps cleaning some things up and adding another large engine oil cooler sitting at the rear above diffuser to keep things cooler Next day - Tuesday - on Dyno - killer wikid awesome pumped out really good numbers - more mid range and on lower boost levels Wednesday - first prac - all day again getting the suspension right - had to borrow front suspension again - out do a lap come in - out do a lap - in - what i had just couldnt handle the load at the more consistent higher speeds - got a lap in at the end of the day that was pretty reasonable  Put it this way that lap wouldve had me in 4th in Pro am for the whole event - with only 700 hp and used tyres Thurs first official prac day - lap out warm up - then entered a hotlap with above setting and 80% effort took corners 1,2,3 and into 4 car felt awesome -  rear came around out of nowhere bang into the wall near front on at whatever 140 kmph Done, over, gone Just one of those how did that happen apparently as all indications show nothing out of the ordinary Got to spend the rest of the time at the event like I hadnt done before - was actually Ok mainly as I had my family and my boy is 9 and got treated like a rockstar Long trip home, lost a trailer wheel in nowhere land, X5 airbag suspension gave up half way across nullabour and rode on bumps stops (its now completely fine) had to do a 19 hr drive day on day 3 as accommodation got screwed up so just had to keep driving till found a town with some Now to reassess - hopefully the motor and other things are OK but yet to be seen too. There is no easy fix there is no i'll just order that part and get it sent - we'll have a talk to people see what can happen and what the go is but at minimum its rebuild from scratch struts forward and alot of time effort and $ should and if I return and if but maybe/ when  I have the cage tied into the front strut towers - if I didnt have that things couldnt been worse you can say its just a front end but if you know what goes into these cars... you'll know what that actually means in reality   Car was very fast. Disappointing we just didnt get to show it Effort doesnt win you races though     Apparently this is motorsport !  
×
×
  • Create New...