Jump to content
SAU Community

The Sa Wasteland

heslo

By heslo,
in South Australia

 Share

Recommended Posts

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Normsta Experienced

Normsta

Posted
Posted
The lockleys center was all mortgages wasn't it? What did your dad do exactly if you don't mind me asking

Just asked him and apparently he only worked at Lockleys, he was going to move to Bedford Park but he left for another bank.

In relation to the work, I think it was mostly call centre stuff, probably in mortgages. He left some time ago so I can't be exactly sure.

Carbon 34 Grand Master

Carbon 34

Posted
Posted
anyone here good with electronics and know much about LEDs

tryin to work out how u compare the brightness of LEDs to incandescent globes. im making my own LED tail light replacements for the 4WD (not ricey altezza styles, basically removing the incandescent globe and having a panel of LEDs behind the factory lenses).

Using those LED Globes u can buy off the shelf is useless, they dont reflect right and are dull in my fittings. Want something that is bright in the day, but not stupid bright at night. The fittings im making will be more waterproof than my standard lights too :)

Matty the LCD works in MCD's which compares to the light colour spectrum. you also need to take into account the light spread , which is very focused on most LED's compared to a normal globe which is why they can look like a hotspot

the newer flat mount LED's are brighter and disperse light much better.cost a lot more though.

voltage on most LED's is not 12volts, you need a resistor to use them, OHM law comes into play depending on how many you use, LED's don't like forward overcurrent and will blow if they see too much. and on some Nissans and other cars the light globe curcuit senses a blown globe and when you put in LED's it flashes on all the time unless you compensate for the lost resistance .

take a look at this site, might give you an idea

http://www.gizmology.net/LEDs.htm

to buy LED's here cost too much, order from China, way cheaper , 20 bucks buys a huge bag full with resistors

I can help you but to create a panel of LED's to look decent can take a lot of trial and error.

Carbon 34 Grand Master

Carbon 34

Posted
Posted
They look familiar...looks tuff 10mm bolt on will fix that

I like it with GTR wheels , gives it the updated look without going obnoxiously over the top anyway

looks like its already so wide it flicks muddy water down the door..lol

huge cheap ass spacers = fail

GoAhead Rising Star

GoAhead

Posted
Posted

The engine light on my R34 has come on, it has come on before but normally goes off within 5 minutes but not this time, has been on for a few days. any idea what the problem might be? or should i go and get a diagnostic done? if so where would be a good place to go?

nicr4wks Experienced

nicr4wks

Posted
Posted
The engine light on my R34 has come on, it has come on before but normally goes off within 5 minutes but not this time, has been on for a few days. any idea what the problem might be? or should i go and get a diagnostic done? if so where would be a good place to go?

Nissan?

Or someone with a consult cable.

CRoNic... Grand Master

CRoNic...

Posted
Posted
The engine light on my R34 has come on, it has come on before but normally goes off within 5 minutes but not this time, has been on for a few days. any idea what the problem might be? or should i go and get a diagnostic done? if so where would be a good place to go?

Doesn't that normally mean the timing is stuffed or it's 'pinging'? Or is that only if you have a PowerFC plugged in?

Or I might be completely wrong altogether.

Nightcrawler Grand Master

Nightcrawler

Posted
Posted
The engine light on my R34 has come on, it has come on before but normally goes off within 5 minutes but not this time, has been on for a few days. any idea what the problem might be? or should i go and get a diagnostic done? if so where would be a good place to go?

Yep I can diagnose without seeing the car - there are only about 120 or so errors that can make your check engine light come on ;)

/sarcasm

GoAhead Rising Star

GoAhead

Posted
Posted
Yep I can diagnose without seeing the car - there are only about 120 or so errors that can make your check engine light come on :down:

/sarcasm

only 120? i thought you were good enough to know exactly which one haha ;)

ive got it booked in tomorrow, hopefully its nothing to serious

Nightcrawler Grand Master

Nightcrawler

Posted
Posted
only 120? i thought you were good enough to know exactly which one haha :)

ive got it booked in tomorrow, hopefully its nothing to serious

Haha yeah hopefully it is nothing. Have you checked ALL of your fluid levels - sometimes it is something that simple. My cas plug used to also come unplugged a little bit on my R34 which would throw an error code that would come and go - maybe give yours a wiggle and see if it is loose at all? Good luck with it, anyhow!

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Rezz
      Chris' Toyota Mark ii JZX110

      By Rezz · Posted

      Seems like a decent result for a modded JZX110. They are bulky in comparison to the 100 and 90 models (which I'd prefer myself) but they are getting very few and far between here in JP these days. Thanks for the detailed review and the import process into the UK. I also have a car which I'm hoping to export from Japan at some stage so it's good to know if someone from the UK was interested in it. By the way the corrosion underneath is par for the course for cars which were located in/near the mountains or along the Japan sea coastline. They get huge amounts of snow every winter and the sodium chloride is used on the roads. Many cars have some kind of rubber like treatment underneath but they tend to limit it to the wheel arches underbody and fuel tank. Suspension arms and sub-frames will have similar corrosion to your JZX110 which is a common sight. See it all the time and car dealers here generally don't even mention it unless asked.
    • Kinkstaah
      new 1.5 LSD issues/concerns

      By Kinkstaah · Posted

      If the sound goes away when you clutch in, the 1.5/2 way diffs are just shit, and you are a normal person. The diff is likely "fine" but driving at anything under 30kmh is a violent horrible experience. It would be exaggerated with solid diff bushings and subframe bushings if you have those.
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      Trailer got new mudguards to accommodate the new wheels Lightweight ally Painted, stickered and done ✅ 👌  
    • MBS206
      What accelerator cable can be used with greddy plenum

      By MBS206 · Posted

      Did you hit up the search function? R33 and greddy and cable returns this thread with some options.   https://www.sau.com.au/forums/topic/358214-rb25-throttle-body/
    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      Thanks buddy.. the standard one needs to be about another inch or inch and a half longer. Thanks anyway
×
×
  • Create New...