Jump to content
SAU Community

Recommended Posts

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

easiest way to bleed nissan clutches is to have 4 hours and plenty of beer spare, or buy a 1pc braided line from master to slave and p1ss the balance block and damper pipe off. Most good workshops will follow the factory service manual and pressure bleed it with a vacuum device :/

Cheers, but its definately not the hydraulic system...

I had a similar issue, didn't crunch gears but was sticky as f**k. Clutch fork had spun on the thrust bearing and the slave was pushing the fork on an angle etc etc, it was really messy. It was all replaced before any serious dramas but frusterated the f**k out of me.

Yeah its weird.

JMW has seen it in person this afternoon, got him a bit stumped too.

Its got to be the pivot or fork.

Congrats! Looks like a beautiful puppy. Please make sure you train and exercise it properly and love it dearly.

Sorry Steve but I'm going to call bullshit on that statement.

I have volunteered at the Lonsdale RSPCA in the boarding section for over 18 months now where we have a minimum of 70 dogs every day and up to 120/130 dogs per day on long weekends. After looking after, walking, playing with, feeding and grooming 1000s of dogs I can tell you that temperament problems have nothing to do with cross breeding.

Dogs are the most loving and loyal creatures (to humans) on the planet. Temperament problems that can occur will usually be due to the humans that come in contact with the dog, its surroundings and everyday life, if the dog has been attacked before, or in some cases mental illness (just like humans have).

As someone who studied genetics I can tell you that 'pure bred' dogs have suffered from generations of in-breeding, usually grandfather & granddaughter mating, and IIRC in some breeds there are less than 50 variances in their genetic code, ie they are closer to extinction than the Panda Bear. I will need to search to provide a reference for that statement though. Cross breeds vary the genetics of the dog and are therefore likely to live longer and suffer less illness. I had all this info on my old C: drive which died so I'll have to search for the books again to elaborate further.

Hence why i lol'd at steves comment.

will definately be a great addition to the family, i always wanted to have a child and dog grow up together

just as i did when i was a kid.

got a quote from ''jetpets'' today, they want $280 to fly him from pt lincoln to adelaide...

yeah, not a bad price, but im not sure if i trust them lol

Hence why i lol'd at steves comment.

will definately be a great addition to the family, i always wanted to have a child and dog grow up together

just as i did when i was a kid.

got a quote from ''jetpets'' today, they want $280 to fly him from pt lincoln to adelaide...

yeah, not a bad price, but im not sure if i trust them lol

My dog is the same as the one your looking at. Same cross etc.

Best dog ever! So loyal, fun, playfull and bulk so scares some people but she's great with people and kids! She's getting a bit old and I don't think there's much left in her :O

when she was young she was very energetic and wanted to sus everything out but that just made it even better to have her around.

Not sure what I'm getting at with this post anymore haha but just saying you won't regret getting that cross bread :banana:

Alot of SA people are going to the Kadina Show and Shine this weekend, so you might not get much of a response. And maybe dont include the meet location, unless you want unwanted visitors, and i dont just mean cops! :P

nar thats cool its all above board nuffin dodgy going on and everyones welcome even a holden or 2 :ermm:

and if we dont like the company iam sure they might get lost from the pack if we try hard enough :D

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...