Jump to content
SAU Community

Recommended Posts

Spotted a silver R32 waving at me as we got out of Dural Carwash this evening. Sorry couldn't wave as was too busy controlling the car!

Also spotted silver R32 GTR (GTR-32X) parked on John Road while I was driving back home.

That was me waving at ya :)

spotted a silver R32 GTR with GTR XXX plates in hornsby heights - sydney road - i was one of those guys playing cricket and waved :)

Spotted that bucket as well, down the same street infact. He'd usually wave back but I suspect he would have been giving the girls his TopGun/Mavrick look.... :D

Spotted MIS 33R in castle towers doin some chrissy shopping yesterday ,

also spotted red 32 going down gilbert road while i was putting up cardboard signs for a garage sale....Sounded noice...

Also just had some fun with a white r34 on roberts road bout 1030, no wing, looked pretty stock, still went though.

saw rukus and hashpipe turning out of some road (im shocking with road names) onto another raod (oh god), in dural/cherrybrook, haha, im descriptive, rukus knows where! got a wave from him, but i think hashpipe was in the zone.. eyes fixed fwd :D

oh and i think that was yesterday.. cant remember for sure, ive been through that way to the city soo many times this weekend, lost track

Edited by ranicx
sam you better not be talking about me !!

Its not electrical tape....its "genuine" Nitto automotive tape :D

hahaha wasnt you, were you parked at stockland mall in baulkham hills yesterday?

noooo

Spotted white r32 GTST with white rims outside the kebab shop (brothers kebabs) at banksia at about 145am today

Maybe it was BWA?

omg that wasnt me

someone copied my car :)

i thought i was the only one not fair they need to change their rims or something

spotted FEAR on greatwestern HWY parra,

and 2 r33 gtst's one winered other black, same road in the arvo.

haha that was me driving brad's car (FEAR)

i was getting frustrated with the traffic let me tell u *#$*@#$

didn't see you though, where were u?!

Edited by d0p3y
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...