Jump to content
SAU Community

R34 Gt Ignition Problem

durty 4

By durty 4,
in Engines & Forced Induction

 Share

Recommended Posts

durty 4 Rookie

durty 4

Posted
Posted

Hey all,

New to the forum but have been a long time lurker.

Have been faced with a strange problem on my 1999 R34 GT. Sometimes when ive been starting the car the MIL (engine check light) comes on and the car tends to shake a bit more than normal, noticing this i realised that it runs on 5 cylinders instead of 6 when it lights up. :)

However the light will only light up once or twice a week and the car runs fine (all 6 cylinders working) whenever I happen to start the car and the light does not show up.

I managed to get the ECU scanned recently when it lit up and the error code 21: Ignition Signal Circut came up.

Is it likely that this is due to a faulty coilpack or related to the crank angle sensor?

Has anyone else had a problem similar to this?

cheers

matt

Link to comment
https://www.sau.com.au/forums/topic/292294-r34-gt-ignition-problem/
Share on other sites
666DAN Grand Master

666DAN

Posted
Posted

Most common R34 problem in the world, replace the coil packs as they all die eventually and you'll be running on less and less cylinders until it won't go.

I don't know of a single R34 that has not had this issue.

James Kelsey Newbie

James Kelsey

Posted
Posted

Just a word on this: I went a cheapo route and just bought one new Nissan coilpack before I learned about those coilpacks and regretted it. I ended up having to go back and buy a full set of 6 Splitfires. Haven't had a problem since... and now I'm having the same problem on the "new" 25GTt I just bought - need to go tomorrow and buy another set. :cry:

skylinelova07 Contributor

skylinelova07

Posted
Posted

Hey matt, I had this problem when I was helping my brother switch engines in his Datsun 1600. We were running on 3 cylinders instead of four. This was due to both electrical problems but we also found out that we had a couple of vacuum leaks which of course does not allow enough pressure for the pistons to work properly. However, from the sounds of things, it seems that your problem may be electrical (coils).

Good Luck with it.

Luke.

R34 -_- Community Regular

R34 -_-

Posted
Posted

iv replaced all my coils about 8,000ks ago and now im getting a missfire in the low rev range while cruising, but the check light DOESN'T come on like it did with the faulty coils. spark plugs maybe?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Marek
      Hi everyone.

      By Marek · Posted

      Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • DanMac34
      R34 Speedo not working after manual swap

      By DanMac34 · Posted

      Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • joshuaho96
      Speed Sensor replacement

      By joshuaho96 · Posted

      Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • QB6SAGR
      Tein Circuit Master- rebuild worth it?

      By QB6SAGR · Posted

      Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
×
×
  • Create New...