Jump to content
SAU Community

Disappearing Oil

Don Dada

By Don Dada,
in Engines & Forced Induction

 Share

Recommended Posts

Don Dada Mentor

Don Dada

Posted
Posted

Hi guys

I've noticed my Rb26 (R33) slowly looses oil over a period of time.

I've done two oil changes so far since i've had the engine and had to top up about 3/4 to 1 quart over the 4000km i run the oil for.

The first time i used Redline 20w50 and thought it was just probably the oil so i tried Schaeffer 20w50 but same result.

There are no oil leaks anywhere and when i opened the catch can after the two the oil changes there was only just enough oil just to cover the bottom(greddy)..... just a few drops really.

Compression reads: 172 / 175 / 173 / 170 / 156 / 160.

There is no smoke on start up, and my friend who was driving behind me says there is only some black smoke for a few seconds when i floor it.... no blue smoke.

It is running really rich because it has a little soot on the back and pops every now and again when a let go.... stock ecu running 12psi

Other wise car pulls really good

Where does my oil go???

Link to comment
https://www.sau.com.au/forums/topic/293879-disappearing-oil/
Share on other sites
The Dan Grand Master

The Dan

Posted
Posted

Check your cam cover gaskets. Notorious as shit on any skyline of its age. I'm forever replacing them for customers that lose around half-1 litre of oil every 5000km.

And it won't be your oil control rings, all they do is drag oil up the bore. Even if you were referring to the second ring it wouldn't be that unless it was blowing smoke, which he said it wasn't.

The Dan Grand Master

The Dan

Posted
Posted

The only reason why I'm repeating it is because when you are losing oil...and you know you have a leak somewhere....no matter how big or small, fix the leak first, then ask the question.

It's common sense. It's also at the top of the engine so it's the best place to start considering the oil will move in a downward direction.

Here's a picture of a GTST with a normal leak from the rocker cover gasket.

post-10554-1257283807_thumb.jpg

It was also leaking from the front corners behind the top timing cover backing plate and leaking from the half moon seals at the back and leaking down on top of the gearbox.

This one appeared not too bad from the top. It wasn't until looking from underneath that you will see where it is coming from.

BeEnAr Experienced

BeEnAr

Posted
Posted

My 32GTR is daily driven about 110km each day of the week and I don't lose oil like you are stating. I had the rocker cover leak at one point but just tighten the screws up regularly now and don't see the issue anymore. But it is apparently a common thing for the rocker covers to work lose.

Don Dada Mentor

Don Dada

Posted
  • Author
Posted

Nissan says the standard is 170 psi with a variance of 14 psi across cyl so the lower numbers (156,160) is what i would actually expect for an engine with this kind of mileage .....water pump,timing belt,tensioner etc. has already been changed in Jap.

Its the higher numbers that has me baffled bc i tested a next 26 with a genuine 25k on the clock using the same gauge and all cyl were between 162-170

The Dan Grand Master

The Dan

Posted
Posted
Nissan says the standard is 170 psi with a variance of 14 psi across cyl so the lower numbers (156,160) is what i would actually expect for an engine with this kind of mileage .....water pump,timing belt,tensioner etc. has already been changed in Jap.

Its the higher numbers that has me baffled bc i tested a next 26 with a genuine 25k on the clock using the same gauge and all cyl were between 162-170

Did you have a jump pack connected, throttle fully open and all spark plugs out for the compression test?

If not, then the results don't mean anything as they will most likely be a few psi off...usually under

Beer Baron Grand Master

Beer Baron

Posted
Posted

I have never had to top up oil on any of my RB26s and i've had a fair few, from stock 1989 engine to brand new N1 Nur motors to built motors and none of them used oil between changes. granted my changes tend to be fairly quick as most got some track use and get fresh oil then, but they always gave back out pretty much what was put in. there is definitely something wrong happening. in normally healthy state RB26s do not burn or loose oil.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • MBS206
      Could it really happen......

      By MBS206 · Posted

      Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • MBS206
      R34 25GT Engine Light 21

      By MBS206 · Posted

      Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...