Jump to content
SAU Community

Recommended Posts

Hi guys

I've noticed my Rb26 (R33) slowly looses oil over a period of time.

I've done two oil changes so far since i've had the engine and had to top up about 3/4 to 1 quart over the 4000km i run the oil for.

The first time i used Redline 20w50 and thought it was just probably the oil so i tried Schaeffer 20w50 but same result.

There are no oil leaks anywhere and when i opened the catch can after the two the oil changes there was only just enough oil just to cover the bottom(greddy)..... just a few drops really.

Compression reads: 172 / 175 / 173 / 170 / 156 / 160.

There is no smoke on start up, and my friend who was driving behind me says there is only some black smoke for a few seconds when i floor it.... no blue smoke.

It is running really rich because it has a little soot on the back and pops every now and again when a let go.... stock ecu running 12psi

Other wise car pulls really good

Where does my oil go???

Link to comment
https://www.sau.com.au/forums/topic/293879-disappearing-oil/
Share on other sites

Check your cam cover gaskets. Notorious as shit on any skyline of its age. I'm forever replacing them for customers that lose around half-1 litre of oil every 5000km.

And it won't be your oil control rings, all they do is drag oil up the bore. Even if you were referring to the second ring it wouldn't be that unless it was blowing smoke, which he said it wasn't.

The only reason why I'm repeating it is because when you are losing oil...and you know you have a leak somewhere....no matter how big or small, fix the leak first, then ask the question.

It's common sense. It's also at the top of the engine so it's the best place to start considering the oil will move in a downward direction.

Here's a picture of a GTST with a normal leak from the rocker cover gasket.

post-10554-1257283807_thumb.jpg

It was also leaking from the front corners behind the top timing cover backing plate and leaking from the half moon seals at the back and leaking down on top of the gearbox.

This one appeared not too bad from the top. It wasn't until looking from underneath that you will see where it is coming from.

My 32GTR is daily driven about 110km each day of the week and I don't lose oil like you are stating. I had the rocker cover leak at one point but just tighten the screws up regularly now and don't see the issue anymore. But it is apparently a common thing for the rocker covers to work lose.

Nissan says the standard is 170 psi with a variance of 14 psi across cyl so the lower numbers (156,160) is what i would actually expect for an engine with this kind of mileage .....water pump,timing belt,tensioner etc. has already been changed in Jap.

Its the higher numbers that has me baffled bc i tested a next 26 with a genuine 25k on the clock using the same gauge and all cyl were between 162-170

Nissan says the standard is 170 psi with a variance of 14 psi across cyl so the lower numbers (156,160) is what i would actually expect for an engine with this kind of mileage .....water pump,timing belt,tensioner etc. has already been changed in Jap.

Its the higher numbers that has me baffled bc i tested a next 26 with a genuine 25k on the clock using the same gauge and all cyl were between 162-170

Did you have a jump pack connected, throttle fully open and all spark plugs out for the compression test?

If not, then the results don't mean anything as they will most likely be a few psi off...usually under

I have never had to top up oil on any of my RB26s and i've had a fair few, from stock 1989 engine to brand new N1 Nur motors to built motors and none of them used oil between changes. granted my changes tend to be fairly quick as most got some track use and get fresh oil then, but they always gave back out pretty much what was put in. there is definitely something wrong happening. in normally healthy state RB26s do not burn or loose oil.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...