Jump to content
SAU Community

Recommended Posts

  • Replies 114
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Really it looks blue?? Thought it was green..

nah nah no contacts.. I added it in.. I went overboard with that pic.

But please let me know what colour eyes you see coz i got a new lcd screen yesterday. Still not use it :D

Edited by siddr20

hmm interesting.. Will check out that pic on another monitor.

I should have just saved more money and bought a IPS panel monitor than this rubbish TN crap.. AARGH!!

Cheers mate.. Im happy for my 1st time in a studio by myself... Prior to this i only took 5-10 photos as i was only there to help another photographer. Was eager to get back into a studio and try it out.

Its deff hard trying to control the lighting.

Going to get the monitor calibrated tomorrow. Hopefully the colours improve on my screen.

In regards to lighting - Well it varied for each shot. But i used three strobes all up.

One to over power the backdrop on most photos.

The other two strobes had different setups - ie. One had a beauty dish and the other had a large softbox attached to it. Or at times i only used the beauty dish and one strobe to overpower the backdrop.

The last pic i posted had no backdrop light.. I used two strobes only, with main light on small softbox at 1/2 power and the other large softbox as fill light at say 1/8th power or so.

So honestly it varied depending on shot and what i wanted.

Thanks miss petepie :) Appreciate it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...