Jump to content
SAU Community

Recommended Posts

  • Replies 138
  • Created
  • Last Reply

Top Posters In This Topic

Dan...it's a carnauba paste made from only the best Brazillian soccer players. Apparently just breathing in the vapours will suffocate you with a thick layer of carnauba oxide. Using it to port and polish your head will make the ports so slippery, air actually accelerates as it travels into the combustion chamber, creating some form of pseudo forced induction.

Well that might be stretching the truth but it's a very cheap and very awesome wax...couple of the boys who were at the photo shoot the other night will vouch for that :P

If only I had the time to put on two layers :D

Wicked! I'll be there... fresh paint does wonders!

Is there any categories for best CHICKS skyline.. lol

So much for equal opportunitys and all that.

It will have a hair tie on the gear stick if its a chicks...

unless your mrs drives your car too :P

I will try and make it down to have a look, but the stagea is getting looked at, i am helping a mate move and the 32 isnt show worthy, so I will not be entering either car. Stagea is nice and clean but hardly show worthly.

Want to see your GTR anyway Chris...

btw PEARL JAM WAS AWESOME.

that is all :D

BTW, Ash, will someone have spare SAU stickers for members to purchase on the morning to have all the cars in the SnS wearing one, making the club a bit more visible?(kinda hard to miss an SAU sticker on every car you look at :blink: )

Ahhh you idiot Birds, sure your car is clean but you'll be sleeping in it for most of tomorrow lol. Thought I'd give it one last wash on the way home from what was supposed to be an early party...gotta give me credit for the dedication!

I was gonna be there but im guessing that after discovering a small injector leak and estimating a loss of around 10 litres between Berwick and Pakky, i dont thihnk its a good idea to drive the GTR....

Well I won't go into detail with what I had this morning but there's no way I could have stayed at a static car display all day! Weather turned out awesome for yas...overcast with no rain is the best for viewing waxed up beasts. Lol TJ no wasted effort there ;)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...