Jump to content
SAU Community

R32 Pwr Radiator 50mm Dual Pass With Oil Cooler


Recommended Posts

  • Replies 89
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

How long do we have to get into this GB. How many spots are left?

Also what kind of oil temps can we expect with this? Should you also run an external air to air exchanger or is this one good enough? My car gets a lot of use as a track car and I don't want to worry about oil temps or water temps.

you would expect you oil temps to stay teh same as your water temp

people in aus using on of these typically see just under 90 degrees water temp on a 36 degree day at the track

pete

they make a twin pass for a r33 gts

are the gtr one the same

??????????? dont know???????? there web site lists different part numbers.

I was looking at the web site and was thinking more along the lines of the 42mm (PWR2272) or the 50mm ( PWR0117), and just run the std rad cap and no internal oil cooler.

so do they have a power steering cooler and oil cooler, or just a p/s cooler? people i've spoken to down here have said they do a good job of cooling the oil, but also do a good job of heating the coolent up

I take it this will come with a spot for a over flow bottle hose?

Whats the best way to control the thermo fan? using a thermo switch like pwr sell ? http://www.pwr.com.au/#/view=products/s=as/

I run a pfc so i dont think it will control it.

Will there be a spot on the radiator to screw the switch in ? according to pwr they turn the fan on at 90 and off at 85.

As soon as i hear back from fatz ill deposit the money.

Some advice on this would be good.

Thanks

Tim.

depends how you run it

i run a thermo on the heater line that just turns on when required

other run the fan full time

its really up to you prefered way

but there are bungs so you can plum several things in

ill put up a diagram this week that show you what we are getting

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...