Jump to content
SAU Community

Recommended Posts

that and the bang bang puter, had to of upset the bearings

no i dont think knock was only ever 30 odd at bang bang, it was definitely already damaged before then

What type/brands of oil are getting ditched at 5000Kms?

i used to use Nulon fully synthetic a lot of people go for motul

its to do with synthetic oils passing by the rings and burning out your exhaust so when people say "oh it doenst burn oil' there mislead

i used to think the same 10000 is fine with synthetic but better safe than sorry

there is also a better reason but i cant explain it as good as i was told it :P but thats the gist of it

The reason I ask is, in the time I did 10,000 Kms I didn't need to top up the oil level at all. When I drained it, it was of course dirty coloured but certainly didn't look contaminated (ODO now reads 119K and I've never had it past 5.5-6K RPM).

A few people I spoke to suggested using Motul 8100 or 300V and changing at 10,000 simply because the oil is of a much higher specification than that used in 1995 when the engine fired up for the first time in the Nissan plant. I don't really know, this is my first turbo car!

keep in mind that 2 things stuff up oil....fuel & heat.....hence why regular changes in summer are handy not to mention tired motors need the oil dumped more often cause of fuel by-passing old rings

EDIT: and as Adrian said, peeps that boost more than others need to be more regular also (because of greater fuel by-pass under boost)

One that was daily driven to work, running stock boost should though..

My 20 only lived to about 105,000 before she died. Car was pretty much stock. Sometimes they just die young :P

I use fully synthetic and change it at 10,000, is there any particular reason why RB's need changing at 5000?

I thought it was for the turbo's. Turbos aren't supposed to like contaminated oil, wears out the bearings sooner.

And here's another I heard, that all these "race quality oils" we use dont have any detergents in them and cook mega easy because they are designed only to be used for say one trackday and then be thrown away...

We need oil Mythbusters :D

Chad, I guess mine fared a little better than yours then :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...