Jump to content
SAU Community

Recommended Posts

I cant find any actual guides on how to do it or where your meant to drain and fill it up from?

Has anyone got any pics of where you need to drain and top it up? or can you explain where it needs to be done cause my car definately needs it.

Technically its not that hard....

There is a drain plug on the bottom of the gearbox, you cant miss it,

it in the centre right at the lowest part of the gearbox.

The filler plug is half way up the passenger side of the gearbox, just follow up

from the drain plug.

When you do it clean the metal shavings of the metallic drain plug, and easier if you use a hose into the filler plug to fill.

I havent been able to do it yet, i couldnt get the filler plug off (car wasnt high enough of the ground!)

And its exactly the same for the diff...

as nissky said, thats all correct. The plug is a bitch to get off, and make sure u can take off the filler first, (if u drain first then can't undo it, ure fkd :D).

Really need a hoist to make it easier, and probably worthwhile to pay joe mechanic $30 to do it for u.

Ill also vouch for redline :(

as nissky said, thats all correct. The plug is a bitch to get off, and make sure u can take off the filler first, (if u drain first then can't undo it, ure fkd :)).

Really need a hoist to make it easier, and probably worthwhile to pay joe mechanic $30 to do it for u.

Ill also vouch for redline :)

You arent ****ed in a way. I have done it on the ground a few times and have always been able to get it off with a 17mm spanner, although its a long one, but if you cant then just fill through the gear stick on a Gtst. It ussually takes about 2L.

unless u have 1/2 decent tools just get a mechanic to do. the ease of the job will be mostly dependant on how tight the last person to change the oil did the bolts up. based on how hard my side plug was done up i have visions of an overmuscled, non-too-bright lad doing the last oil change on my car

Do you have to change the filter on the Manual gearbox? Is there a filter on the Manual boxes?  

I know that when changing oil on an auto box, you need to replace the filter aswell. Is this true for the Skylines?

there is no filter on a manual box. The bottom drain plug is magnetic to collect metal particles though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...