Jump to content
SAU Community

Recommended Posts

  • Replies 224
  • Created
  • Last Reply

Top Posters In This Topic

Hi Guys,

Thanks alot for the good turnout on such a hot day :P I've now had a swim and a beer, so life is good.

I'll post up the final results tommorow, but for now.

RB26 & Outright - Bart R32 GTR -540AWHP

RB25 - 3BPEKA - 438rwhp

NA - BrockAC - 383rwhp

Some of those figures are off the top of my head, so I'll correct them all tommorow once I recover.

A huge thanks to Alistair and the crew at AutoWorx, they did a great job under trying conditions :cool:

Cheers

Paul

Heaps of people today, was good to see a big turnout, thanks for coming down everyone & thanks to the Autoworx crew for having us :P

I think the only sunburn I got today was on the back of my neck... Although I can't see it so I don't know, so if I can't see it, it's not there. Sunburn free day woo!

Was pretty damn hot out... still feeling it now.

Thanks to Autoworx for letting us play with their dyno.

Once I get the dyno readout data forwarded to me I'll start plugging it into the comparison tool. Unfortunately the runs were in KM/H instead of RPM, so comparing the GTR's to the GTSt's wont really work too well, we'll see when I start putting the data in.

I'm converting the videos now, I think I got everybody apart from the first 4 cars (sorry guys) - should all be in 1080P HD glory. Camera managed to do an okay job of picking up the sound too.

Photos are uploading as we speak, will post them up in a few minutes.

Oh and I thought my 236.5rwhp was a pretty good effort for a stock turbo R33 - bit lower than my Hyperdrive figure from when I got it tuned last year (was about 245rwhp) but car really needs another tune and a better boost controller.

Mark's R33 (the wine red one that took the place of my GTR on the dyno today) has a previous readout from a few months ago showing 392rwhp. It's amazing how a change in temperature can make such a difference on the dyno. The intake temp on the previous sheet shows 8C lower temp than todays one (28C vs 36C) however the graphs are almost identical. Not an exact science is it hehe

Videos are still uploading *sigh* god damn high def.... 20GB for less than 40 minutes of footage...

Here they are so far, I'll keep adding them to the playlist as they upload -- they should all be in order:

SAUWA Dyno Day - Youtube Playlist

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...