Jump to content
SAU Community

Recommended Posts

  • Replies 216
  • Created
  • Last Reply

Top Posters In This Topic

Dudes,

I had a set of these on my old GTSt (now owned by MattyB). They have a 4 or 5 step change from blue to green and a 4 or 5 step brightness control too. They look awesome at night, and there is no reflection off the windscreen as Gus said the 'hood' of the dash covers them... They are not hard to install as they sit over the top of your existing guages.. Only problem is you either have to cut through the EL to get them over the needles or take the needles off which unless you are ultra careful will result in incorrect speed, revs, temp, fuel etc....

Definately worth the money...

Rice is nice sometimes... ha ha ha

*raises hand*

If we're looking at Jan/Feb then I'll be in for $200 for EL Kit also...I've wanted some for AGES!

fane,

We can do ours together, I've done some before!*

*Cannot gaurantee accurate speedo afterwards tho! (it's a bitch!)

$160 thats gotta be a bargain

and ina group buy might even be cheaper.

the ones i was trying to organise are going to be $200+

no chance in hell. so I canned it.

guess its down to autoworx and car quest and the spoiler shop

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...