Jump to content
SAU Community

Recommended Posts

Hey everyone

Just put some new rear shocks in my car (Series 1 R33) and I just had a question about whether this looks right to everyone else. Is this the right way for the shock to be facing or should it be facing towards the tyre. It looks ok to me because it has the damper adjuster facing towards the diff so its easier to adjust, but I bought some springs and they had this instruction manual in JAPANESE mind you which had this picture and it looked like that metal spacer thing on the bottom of the shock is facing towards the wheel.

So Im a little confused. What do other peoples one look like? Not sure if it really makes a difference but ye.

Thanks in advance

post-14546-1260394326_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/299621-shock-absorber-installation/
Share on other sites

Haha ye well I figured that much to but I looked at my brother's car (its a commodore mind you) and it had shocks with a larger spacer like mine and that was facing in the same direction as mine. I actually just also asked my mate who works as a mechanic at nissan and he reckons people there said it looks right but no one has been able to explain what the difference is.

That's why I thought if people can look at their own skylines with aftermarket shocks then maybe we can get a trend going on what theirs looks like.

How is the setup on your rear shocks Munkeyboy?

Hrmm I see. Thanks for the quick reply at least I have one other 'skyline' to go of. Did someone tell you to face it that way for a reason or did you follow instructions or ....?

Thanks again

My billies have the spacer towards the mounting point ie as per instructions.

On the front ones the billies don't have the spacer [well I didn't get any supplied] so I measured up a couple of thick washers and used them.

But I reckon they would rub if they weren't spaced at the front, the back I becuase they said and to keep the geometry right [someone had to have figured it out before, that why they say to do it that way].

Thanks for the reply tridentt150v, that looks like 2 down for facing the other way. Any other people want to join in and tell me how theirs are facing ( and make me have to pull them out again arghhh)?

Hrmm I see. Thanks for the quick reply at least I have one other 'skyline' to go of. Did someone tell you to face it that way for a reason or did you follow instructions or ....?

Thanks again

They were fitted that way by my mechanic, who has done it a million times. no instructions

Ok thanks MunkeyBoy, well I decided to go down and ask pedders for some free advice and the guy there who seems like he knows what he is talking about said that it shouldn't matter if both ends of the eyelet spacer thing has the same diameter(which mine has) but if one end is slightly larger of tapered than that end should go towards the bolt I think. He said they sometimes do that for clearances or something like that. I put the front ones in yesterday but I decided to buy a washer as Tridentt did and put that in there which makes it look ok.

Thanks for the replies people, I will keep an eye on it and if it makes noises etc then I will change it and see.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...