Jump to content
SAU Community

Alternator Issue

TiTAN

By TiTAN,
in General Maintenance

 Share

Recommended Posts

TiTAN Grand Master

TiTAN

Posted
Posted

two days ago the battery light came on in my car. Checked the voltage and it looked like the car was running on the battery only. I have just installed a replacement alternator and the issue is still there that the battery light is on and the car isnt making more than 12v.

If you run the car with the jumper leads connected to another running car it idles/revs fine if you disconnect it the fuel pressure drops and the car leans out (i assume thats to do with voltage)

do you think i have gotten a faulty altternator or is there some other electrical issue that people know of that would stop the alternator making any current?

Link to comment
https://www.sau.com.au/forums/topic/300654-alternator-issue/
Share on other sites
mad082 Grand Master

mad082

Posted
Posted

could it be a battery issue where the battery is what is stopping it from increasing the voltage?

there is a way to check this although it isn't the best thing to do. start the car with the battery connected, then disconnect the battery and check the voltage of the alternator then connect the battery again. only problem is that there is a small chance that the extra voltage from the alternator can damage the ecu, but i have seen this done before when jump starting a car without jumper leads.

Bozz Proficient

Bozz

Posted
Posted (edited)
could it be a battery issue where the battery is what is stopping it from increasing the voltage?

there is a way to check this although it isn't the best thing to do. start the car with the battery connected, then disconnect the battery and check the voltage of the alternator then connect the battery again. only problem is that there is a small chance that the extra voltage from the alternator can damage the ecu, but i have seen this done before when jump starting a car without jumper leads.

Do not do this. Easily possible to destroy all electronics on your car and cost you a lot of money in repairs. That was an old trick before cars had electronics, to test if the alternator was working. The battery acts as a large capacitor and supresses voltage surges through the electrical system. Most EFI cars have enough of an idle current draw to keep a regulated alternator from spiking sharply but do you really want to chance it? Have you ever tried to switch on cruise control while your driven wheels were in the air? The reg in the alternator behaves very similar. Massive over and undershoots without the battery attached.

Nissan alternators needs 2 things to properly charge a battery. A voltage reference input and an excite wire. The VRef wire should be attached to the battery positive to measure how much voltage drop there is in the charge wire, to keep the battery fully charged. The excite wire provides a tiny amount of current though the charge light to energize the alternator as it contains no magnets. The excite wire is clearly working (white / red stripe) so check you have 12v on the other wire (i forget the color) on the 2 pin connector.

edit - the white/red wire should be close to zero volts with the engine off, then up to 12v with it running. The other wire on thta connector should have 12v on it all the time.

If the white/red wire still has close to zero volts with the engine running and the other wire has 12v, you have a faulty alternator.

Edited by Bozz
DRD-00F Grand Master

DRD-00F

Posted
Posted

yeah I would have guessed that...

I've had the battery terminals drop off the batery a few times (the negative) and nothing went wrong, besides a quick drop in voltage whenever I turned the lights on... But my alternator is in pretty good nick, I have no plans of needing to change it anytime soon...

The positive terminal hasn't come off since I put the new battery in there about 2 years ago...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...