Jump to content
SAU Community

Almost Stalling On Acceleration

SECURITY

By SECURITY,
in Engines & Forced Induction

 Share

Recommended Posts

SECURITY Grand Master

SECURITY

Posted
Posted (edited)

when i go to accelerate from either a standing start or between gears the car hesitates, goes lean and kind of sputters a bit then goes back to normal. if i accelerate SLOWLY it doesnt do it, and when i accelerate HARD it doesnt do it, im not sure what it is. i tried checking for leaks in the vac/cooler system with no luck.

i took a vid to see if it would help identify the problem. the gauge on the left is the wideband and you can see the pressure/vac/accelerator position on the gauge on the right.. turn up your volume so you can hear what the car is doing.

http://www.youtube.com/watch?v=xPHSLI50Kd4

cheers guys

Edited by SECURITY
Link to comment
https://www.sau.com.au/forums/topic/301603-almost-stalling-on-acceleration/
Share on other sites
DRD-00F Grand Master

DRD-00F

Posted
Posted

well unless he has wired the wideband backwards or some crap, it's definately going lean...

It is a tough one! Maybe there's a small block in one of the injectors? Or the pump isn't getting enough voltage or something? Other then that... I was thinking a stuck throttle body but that wouldn't lean it out...

SECURITY Grand Master

SECURITY

Posted
  • Author
Posted

sorry, shouldve given a run down on the car

its got a vipec ecu, it does it under any load, i tried changing the tune around (the vipec has a 1-100 range) i went from 42 in the cells up to 60 and it didnt change much, im pretty sure its a mechanical issue.

GTR-32U Mentor

GTR-32U

Posted
Posted (edited)
well unless he has wired the wideband backwards or some crap, it's definately going lean...

It is a tough one! Maybe there's a small block in one of the injectors? Or the pump isn't getting enough voltage or something? Other then that... I was thinking a stuck throttle body but that wouldn't lean it out...

My mistake...I didnt see the AFR ratio thing on the left...Definately sounds like some kind of fuel issue. Highly doubt its ignition ( although I could be wrong )....Has anything been done to the car recently ..like prior to this problem occuring ?...Maybe a vacuum line got knocked loose

Edited by GTR-32U
SECURITY Grand Master

SECURITY

Posted
  • Author
Posted
Not sure about the vipec ecu but I had a similar problem on my VH41de safari running a link ecu, it turned out to be an acceleration enrichment issue.

i think you might be on to something, ill have a play around with the accel enrichment tables and see where it gets me.

STATUS Grand Master

STATUS

Posted
Posted
when i go to accelerate from either a standing start or between gears the car hesitates, goes lean and kind of sputters a bit then goes back to normal. if i accelerate SLOWLY it doesnt do it, and when i accelerate HARD it doesnt do it, im not sure what it is. i tried checking for leaks in the vac/cooler system with no luck.

i took a vid to see if it would help identify the problem. the gauge on the left is the wideband and you can see the pressure/vac/accelerator position on the gauge on the right.. turn up your volume so you can hear what the car is doing.

http://www.youtube.com/watch?v=xPHSLI50Kd4

cheers guys

accel pump adjustment

SECURITY Grand Master

SECURITY

Posted
  • Author
Posted
this car has not been tuned yet has it?

not properly, i had it on a dyno after the engine was rebuilt by the engine builder but the new injectors and plenum havent been tuned in properly. i got it running pretty well using the auto tune and the m5, but this problem just started randomly though.

the accel enrichment didnt work. it didnt change at all. i think its something mechanical rather than the tune.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...