Jump to content
SAU Community

Recommended Posts

You said that you wanted to build a 4 door GT-R. Genuine, factory built, GT-R sedans are almost impossible to find.

My point is that doing it yourself by getting a 4 door chassis and transplanting the engine/driveline from a GT-R coupe into it is going to be a massive job with lots of custom work from whichever workshop you eventually get to help you with it. The end result is more prone to failure than a 4 door car that left the factory with an AWD drivetrain, and OEM levels of engineering and testing behind it.

If you're talking about just dropping an RB26DETT into a sedan chassis then it should be relatively simple, and reliability will come down more to how you treat the car than anything else. But, to be quite blunt, the GT-R is defined more by its advanced drivetrain than its engine so that car wouldn't be a "4 door GT-R" any more than some ricer who sticks badges on their GTS-t.

If you intend on having the GT-R's ATTESSA (which is different to the GTS4's ATTESSA) fitted as well as the engine into a sedan, which would make it more worthy of the title, then you're going to need deep pockets and people who really know what they're doing. Even then, I'd still be worried that things had to be kludged to fit/work, which means it's more likely to break than a car that was designed to be that way in the first place.

Check out these threads.

http://www.skylinesaustralia.com/forums/98...Gt-t297401.html

http://www.skylinesaustralia.com/forums/R3...ld-t280439.html

My opinion:

If you are going the R34 N/A route - Keep the 4 door as "daily spec" - With minimal mods. High flow panel filter, extractors and a decent sounding stereo (not the full DOOF DOOF stuff - adds so much weight and takes boot space) and some nice alloys. This will also enable you to get parts from the nissan dealerships.

R34 non-turbo are not quick cars (on par with your typical n/a aussie 6s), however they do keep pace with the "majority" of cars out there - so they are not underpowered by any means. I'd put them as VERY average. Only real advantage of the n/a R34 is the better handling and the good looks (majority of people out there have no clue between the bread and butter GT/GT-T to the GT-R).

When you save up enough you could probably end up having 2 cars :P R34 4 door as a daily and a GT-R for the weekend/having fun...

I just picked up a R32 sedan gtst with Rb26dett conversion

plenty of mods done to it, upgraded brakes, tein suspension, 750cc injectors, ecu, gtr fuel pump, etc

they are around, need to be quick tho when they pop up

about to strip it into a track biatch

unless you want it for 10k ;)

DSC00350.jpg

buy a POS first car cheap as chips

save as much money as you can in the mean time

when off p's buy an ER34 GTT and youll be fine

ER34 GTT to GTR conversion is stupid, pointless, not worth the $ and a waste of time

the money youll spend all up - you could just buy a GTR R34 for the price they are now

the converted ER34 GTT to GTR will be worth nothing in comparison to what you spend

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...