Jump to content
SAU Community

Recommended Posts

Hey Guys.

Selling my bumpers and side skirts.

If anyone can do a pick up i'll sell the lot for $200.

If i have to post $330 + the cost of posting for the lot.

Individualy: Front bumper $150 + post

: Rear bumper $150 + post

: Side skirts $100 + post

The kit is in ok\good condition. There are no cracks but some deep scratches under the front bumper. You can't see them unless your bending down.

All other marks might come out with a buff. :D

But none of that matters if you need to paint it :D

I have taken pics of all worst damage.

post-60315-1262656287_thumb.jpg

post-60315-1262656351_thumb.jpg

post-60315-1262656411_thumb.jpg

post-60315-1262656461_thumb.jpg

post-60315-1262656511_thumb.jpg

post-60315-1262656558_thumb.jpg

post-60315-1262656623_thumb.jpg

post-60315-1262656663_thumb.jpg

  • 4 weeks later...

OK. With "Toll I PEC" $190 for each bumper and $80 for side skirts. That's to Perth and the same to Sydney.

If you bought them all i would send in one package and it would cost at a guess $200 for the lot.

So it's about $530 for the lot to send to Perth or Sydney.

If you live in Perth it would be cheaper to drive here and pick them up yourself. Since i'll sell the lot for $200 pickup only.

  • 3 weeks later...
Hey Paul, can you please get a shipping quote for the front bar to Northgate, SA, 5085? Pretty keen, since I have toasted my stock bar mounts

it would be $190 to get it anywhere in OZ. But when you say "Bar mounts" do you mean just the bumper becasue thats all i got

Yeah I only need the bar mate. Can you get a specific quote for me, as if it is $190 to anyhwere in Oz (Qld for example) then surely it is half that amount to get it to Adelaide which is 1/3 of the distance.

Yeah I only need the bar mate. Can you get a specific quote for me, as if it is $190 to anyhwere in Oz (Qld for example) then surely it is half that amount to get it to Adelaide which is 1/3 of the distance.

It's the same to send to Perth and to Sydney so it would be the same to Adelaide. They told me it don't matter the distance. Thats with "TOLL I PEC". You can use any courier you want and get them to pick it up or tell me where to drop it off localy.

I can double check tomorrow. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...