Jump to content
SAU Community

Recommended Posts

I have for sale the following items:

1. R33 GTSt brake calipers, rotors and pads $500 (If sold seperatly $350 for the Fronts and $150 for the Rears)

2. R33/34 GTR JJR intercooler hard piping kit powdercoated black by Craved Coatings, including silicon hoses $350 (Missing hose clamps)

3. R33 car jacks $30 each

4. R33 push type slave cylinder with line $60

5. RB26 cam cover $60 (will require respray)

6. Exhaust cam bracket $20

7. Stock R33 GTSt BOV with pipe $50

8. R33 GTSt crankshaft and crankshaft girdle $100

9. RB26 badges Large $30 Small $10 each

10. RB20/RB25/RB26 Gates timing belt $80

11. Stock R33 handbrake shoes $50

12. Stock RB25 conrods $60

13. R33 GTSt thermo fan $60

14. R33 GTR front and rear rotors Make an offer

15. Various plugs for radio/headunit $10 each

16. RB26 push in cam cover fitiings -10 size $30

17. N1 oil pump gears $300

18. R33 GTSt manual, series 1 speedo cluster $60

19. Apexi power FC hand controller 415-N001 $350

I am located in Sydney, happy to post interstate at buyers expense

Edited by Smoky
Link to comment
https://www.sau.com.au/forums/topic/302659-rb25-rb26-parts/
Share on other sites

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

5. RB26 cam cover $60 (will require respray)

i'll take this if its the pair of cam covers (like the actual camshaft covers...)

16. RB26 push in cam cover fitiings -10 size $30

and if these fit the RB25 cam covers i'll take them too

Link to comment
https://www.sau.com.au/forums/topic/302659-rb25-rb26-parts/#findComment-5018200
Share on other sites

5. RB26 cam cover $60 (will require respray)

i'll take this if its the pair of cam covers (like the actual camshaft covers...)

16. RB26 push in cam cover fitiings -10 size $30

and if these fit the RB25 cam covers i'll take them too

Sorry, I should have put it as RB26 timing belt cover, no cam covers for sale

To my knowledge they will only fit an RB26

Hi mate, interested in the Apexi Power FC, i still have the stock ecu, is this a plug in piggy back system? or does it replace the whole ecu? thanks, i live in perth btw. oh and it works good?

No Power FC for sale here, just the Hand Controller

Link to comment
https://www.sau.com.au/forums/topic/302659-rb25-rb26-parts/#findComment-5018283
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Did you pay with a credit card? I'd be putting a charge back through then finding a new sparky to sort it out. 
    • If you mean the alarm immobiliser; theyre internal to the alarm itself which makes that difficult; I couldnt even see where he put it; its not in the same place as last time; but with all black wiring it might be very challenging to trace  I had someone turn the key for me as I know it only primes for a couple of seconds As my post above; I am getting no voltage to the pump at all; but I am testing continuity of the power line (SB) from the pump plug to the relay fine. As well as the negative from the pump plug to a 12V constant.    Yeah; he blammed the no start on a bad battery; said I needed to get a new battery and it'll start. Turns out the battery drained because the tail lights had been on for half the day during the install (the rubber cushion on the brake switch gave out while he was testing it as I have a picture of the car from that morning with the tail lights off..i've replaced that). The battery was turning over the engine just fine for a long time; but got low since lights were draining it so it was too low to test a start after he finished. I bought a new one on his advice...$250 wasted. My original battery charged up just fine and is healthy.    It was running perfectly fine when I messed up the old alarm (programmed out the remotes). He couldnt start it after removing the old alarm; my assumption is that when he unhooked it; he didnt bridge the circuit back when trying to start it. Its always been perfectly fine. The ECU swap and pump were 2 years ago. It's never missed a beat in that time. 
    • This is a big issue for me without the diff. I just have zero drive from the passenger side when drivers side has no traction. Bec's parents place has a crazy steep driveway with odd camber and I have never been able to get up. My bro-in-law's 130i with an (unknown brand) LSD gets up fine as does their dad's Hiace. My car stays at the bottom. We have other odd camber roads around here as we're elevated a bit and if it's raining I can get totally stuck around some hairpins. 
    • Yeah, I am super excited for this.
    • Was the car running before he touched the car?
×
×
  • Create New...