Jump to content
SAU Community

Recommended Posts

I would go for a high flow panel filter from K&N or Apexi. You can buy the K&N filter from Autobarn and the Apexi one most i think some traders on the forum sell.

In terms of the pod filter, again I would go for a K&N or Apexi. Depending on which state you're in, not sure if this would be a defect modification for you. Studies have shown the Apexi produces most power with the best filtration with the K&N coming in second best.

Cheers

Pod filters are a waste of time and don't gain any real performance over a high quality panel filter in stock airbox.

You just need to look at the Mines R34 GTR or any Mines car for that matter he uses panel in stock air box.

Go the k&N panel.... :rant:

4 an N/A +1 on keeping the stock airbox with a hi flo panel filter... really not worth it unless ur after hektic induction noise lol, u will need it fully encolsed, CAI, it fully mounted etc 2 much effort lol

4 an N/A +1 on keeping the stock airbox with a hi flo panel filter... really not worth it unless ur after hektic induction noise lol, u will need it fully encolsed, CAI, it fully mounted etc 2 much effort lol

I honestly don't hear any noise difference on an NA motor. Unless the hood is open and I'm sticking my head in to a get good look, I can't hear it.

On a turbo set up, it's pretty obvious.

on some NA cars it's very obvious though. i have had a pod on 3 6 cylinder cars (falcon, commodore and magna) and the falcon and magna it made a massive difference to the intake noise (sounded throaty) but the commodore it didn't do a thing.

A pod will suck hot air from the engine bay if you dont have a shroud for it and some form of cold air intake.

Go the quality panel filter

Hot air = fail

Yes should have explained self better, was thinking of a Pod inside a custom airbox

Pod filters are a waste of time and don't gain any real performance over a high quality panel filter in stock airbox.

You just need to look at the Mines R34 GTR or any Mines car for that matter he uses panel in stock air box.

Go the k&N panel.... :D

Thanks

4 an N/A +1 on keeping the stock airbox with a hi flo panel filter... really not worth it unless ur after hektic induction noise lol, u will need it fully encolsed, CAI, it fully mounted etc 2 much effort lol

Thanks, was just asking as these things are so underpowered, not that I want it going to hard for my leaner daughter.

Just feels so slow compared to my 400rwkw+ BA Turbo.

Will just go with a K&N Panel Filter and look into improving the exhaust.

I went with the Apexi power intake and decided to make my own heatsheild, still not finished the sheild gotta make it look nice.

post-63710-1263319346_thumb.jpg

Cost me about $30 to make it, makes a big difference if its shielded or not

Thats what I was thinking, Thanks

Thanks, was just asking as these things are so underpowered, not that I want it going to hard for my leaner daughter.

Just feels so slow compared to my 400rwkw+ BA Turbo.

Will just go with a K&N Panel Filter and look into improving the exhaust.

i'd be worried if it didn't.....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...