Jump to content
SAU Community

Recommended Posts

now i don't mean to sound rude, but you should learn to use the search function. all the questions you have posted can be quite easily answered with a quick search. or you could've asked them all in the 1 thread.

  • 4 months later...

anyone know the part number that i need for RB25DE? just want some cheap ones as im selling car soon and in the morning it stutters at low revs on cold engine, once it warms up it gets a little better..

any info is great,

thanks

The standard Nickel items are fine, NGK part number BCPR5ES-11 (or BKR5ES-11). The 5 is the heat range, 5 is most efficient on a stock engine, 6 is better for one that receives a regular thrashing and has mild mods (intake/exhaust).

Power gain from different spark plugs is negligible. Platinum’s are less conductive than nickel (i.e. worse) iridium’s are slightly more conductive, but your unlikely to notice the gain, perhaps equally better off with V spark nickels or something,

the most gain with spark plugs can be had by correctly indexing them, so they are all facing the intake ports (middle), you can do this by purchasing thin copper washers, to give you that half turn extra adjustment. some people have even managed it by buying a few packs of plugs and mixing and matching between holes (but copper would be best as it will squash as you tighten, so you can keep the correct tension).

I run indexed BCPR7ES (gapped at 0.75mm with splitfires) on my RB25DE+T with water + meth spray.

Edited by SKiT_R31

Probably find the best info here; http://www.skylinesaustralia.com/forums/Sp...gs-t104405.html

I've never worked with Nissan V6's, but I’d assume it would be the same story as the straight 6's.

Pretty much run what the turbo boys run but a heat range higher. When you change your spark plugs, you can tell if you’re in the right heat range by the discolouration on the thread, if its past 3 thread lines, you probably want a colder plug (test after fitting your 5's)

I used to have Indexed NGK BKR5EY-11's in my N/A RB25, had perfect burn and the plug wasn’t getting too hot.

I generally think your best with standard nickels (what people call coppers, but they are nickel coated, and all plugs have a copper core) and would get the best performance & cost efficiency replacing them more often, than spending 6 x as much on an iridium and replacing it less often. This obviously changes if you have tom pay someone to change them for you, in which case it might be more efficient getting longer lasting plugs, as the labour would cost the difference.

  • 4 weeks later...
Hi guys,

anyone know what plugs i should use in my V35 250GT, VQ25DD engine n/a,

thanks Richard

NGK LFR5AIX-11 Iridiums

NGK list this plug as a direct replacement on the VQ25DD and VQ35DE.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
×
×
  • Create New...