Jump to content
SAU Community

Recommended Posts

Have just purchased first skyline and i'm not sure if the boost gauge is reading right, it generally sits in the negative and only goes into positive boost when accelerating hard, is this normal?

That's what its supposed to do?

Have just purchased first skyline and i'm not sure if the boost gauge is reading right, it generally sits in the negative and only goes into positive boost when accelerating hard, is this normal?

That is the corect operation of a boost gauge. Under no load the intake pressure sits in a vacuum, demonstrated on the gauge as a negative pressure. Once the engine is under sufficient load and the turbo is "spooling" the pressure will go into a positive "boost" it will continue to climb until the wastegate cracks open and the boost will stabilise at a single value controlled by the wastegate/boost controller.

Have a read of this, good article to explain the basics.

http://www.howstuffworks.com/turbo.htm

Edited by PM-R33

k, cheers for that i also wanted to check just below and to the left of the steering wheel there is a screw with a black cap on it that dosen't seem to do any thing is that just for securing some sort of access panel?

another question, is it common for the exhaust manifold nuts on cylinders 1 and 6 to come loose/ fall off, and is there a special nut/washer type to stop this?

Totally normal.

Just kidding dude. Maybe the studs are broken so they arent staying tight?

Best thing to do would be to find new ones and just put them on tight.... tight tight. Maybe even some threadlocker?

Standard gauge isn't the best. Check the line for it hasn't cracked as they tend to do. It comes off the intanke manifold near the firewall, it's a 4mm black rubber hose

I had this issue. The rubber hose becomes brittle and cracks appear which messes up the factory boost gauge. I had some 4mm rubber vacuum hose lying around which I installed and all is fixed with the gauge. Very easy to fix.

I had this issue. The rubber hose becomes brittle and cracks appear which messes up the factory boost gauge. I had some 4mm rubber vacuum hose lying around which I installed and all is fixed with the gauge. Very easy to fix.

Yep, I had the same trouble. That little hose just gets brittle with age. Also causes a vacuum leak, which harms the boost as well.

A few bucks worth of hose from Autobarn should do it!

  • 4 months later...
Standard gauge isn't the best. Check the line for it hasn't cracked as they tend to do. It comes off the intanke manifold near the firewall, it's a 4mm black rubber hose

hi.. thought i would post here.

this hose for the stock clusters boost gauge, has came off, its still connected to the manifold, but it has came off at the other end, i pulled it and it came from behind the drivers guard.. so while ive had my guard off today, i have been trying to reconnect this, but i cannot find anywere it goes?, can some one lend a hand to were this connects back.. thanx

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...