Jump to content
SAU Community

Recommended Posts

  • Replies 124
  • Created
  • Last Reply

Top Posters In This Topic

  • 1 month later...
  • 2 weeks later...

Hey

I was reading ur answer for this not fitting rb25det neo motor, I was wondering why it doesn't fit.

Cheers

Rob

Hey

I was reading ur answer for this not fitting rb25det neo motor, I was wondering why it doesn't fit.

Cheers

Rob

Hey Rob!

The NEO's have a different engine block set-up, the bolt pattern does not match so extensive modifications would be required.

Cheers,

Brendan

(VM)

  • 1 month later...

Just letting you know that these WILL fit a neo motor. My setup at the moment is an rb25de+t neo using an r33 ecu and running an r33 s1 intake manifold to retain sensors for ecu.

The only thing that's different is you need to pull out one stud for the head and replace with a longer one. I did all the work myself and haven't had a single problem.

Just letting you know that these WILL fit a neo motor. My setup at the moment is an rb25de+t neo using an r33 ecu and running an r33 s1 intake manifold to retain sensors for ecu.

The only thing that's different is you need to pull out one stud for the head and replace with a longer one. I did all the work myself and haven't had a single problem.

Hey!

Thanks for the information, I am only going off what customers have noted however I do know that many have used these on the NEO's with modifications.

Do you have any images of your set-up?

  • 2 months later...
  • 1 month later...
  • 2 weeks later...

Hi there could you pm me with a price for a raw cast plenum with adapter for an r33 rb25det. Also do these work with the standard fuel rail? Cheers!

Hi there could you pm me with a price for a raw cast plenum with adapter for an r33 rb25det. Also do these work with the standard fuel rail? Cheers!

Hey,

Will do so now, yep original fuel rail will go straight on no problem.

- Brendan

Hey mate,

Does the plenum take all sensors that were on the stock one? IAC/AAC, vacuum lines etc.

Can you pm me a price for the plain cast finish with stock throttle body adapter to 2750 please

Thanks

Hey mate,

Does the plenum take all sensors that were on the stock one? IAC/AAC, vacuum lines etc.

Can you pm me a price for the plain cast finish with stock throttle body adapter to 2750 please

Thanks

Hi,

Yes mate, takes all the original sensors mate! No mods required with this one.

Will PM you now.

- Brendan

Could u please pm me a price for a raw cast aluminium plenum to suit standard throttle r33 rb25det. Thanks bud!

On it's way....

  • 3 months later...



  • Similar Content

  • Latest Posts

    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
    • hahah when youtube subscribers are faster than my updates here. Yes some vid from the day is up, here:  Note that as with all track day videos it is boring watching after the bloopers at the start.  The off was a genuine surprise to me, I've literally done a thousand laps around the place and I've never had instability there; basically it rolled into oversteer, slipped, gripped and spat me out. On the way off I mowed down one of the instructor's cones and it sat there all day looking at me with accusing cone eyes as I drove past. 1:13:20 was my fastest lap, and it was in the second session, 3rd lap.  It (or me!) got slower throughout the day as it got hotter.      
    • It sounds like you want what the Toyota Landcruisers have for their roof racks. Wanna know what you end up with? Rust holes in the roof, and water everywhere...
    • Discovered today that if I select reverse first and take my foot off the brake, then select drive, the drive indicator light works and so does the tiptronic gear indicator. 
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Does anyone here have any ideas?   Cheers guys
×
×
  • Create New...