Jump to content
SAU Community

Recommended Posts

Hey Rezz do you know any engine specs?

I know that practically every part available in HKS's 1991 engine parts list was used for the Zero R, what those parts actually were however, I don't know.

The whole "Zero R" idea came about because HKS wanted to compete in the '91 Tokyo Auto Salon "Complete Car Grand Prix"... a contest to see who can build the best car based on a stock-from-factory vehicle. Aparently the car was fully engineered to a 270km/h standard (read: safe), and was built for high speed cruising performance, durability, all wrapped up in a well behaved "mature" package. The development budget for the Zero R from idea to complete car was 100,000,000 yen.

  • Replies 95
  • Created
  • Last Reply

Top Posters In This Topic

so how much are these cars for sale now. the one that is going ?

Dude, it's not like we can just click-click-click and find one for sale... you know? I'm sure the owner of the one that is getting about would want at least half of what he paid for it.

Some more pics i found laying around its all i could do..

Some pics arnt of best quality but its hard to find anything decent.

Well done mate...:D

Thats about all the info thats lying around on this car I think... theres precious little left to post about. I hope SAU members can kinda get the picture on how the Japanese mentality works through a thread like this, ie: The Zero R is gone, so why all the interest? (don't take that the wrong way, from a Jap point of view, thats what they think about Aussies getting interested in old(er)skool 'lines) It's an awesome car obviously, but even with the much bigger population in Japan compared to Australia or even the UK, theres about as many people interested in the Zero R in Japan as there are in Australia... read: bugger all.

Sorry guys, it sounds like a negative post, but I just got slightly dissed by my mate Kazuya because he couldn't understand why I was interested in a relic from '91... the R34/V35 is where it's at now!!!

yeh i asked a friend about this car aswell in japan he said its not a big deal.. but the only reason i would love to own this car is because its rare. once a car is rare its worth plenty. .. its like the old gtho phase 3 but with the models being made so little .

Guest RedLineGTR

the thing is there isnt much know or interest about this car or similar examples in general...but people in japan dont bother with old technology and achivements they always looks for the newest and best thing thats why they are ahead in technology i would assume. Also if it was such a great car then thier would be more info about it...

Guest RedLineGTR

this car is rare but so are drag cars that run 7sec down the 1/4 mile flat...power ratings of turbos have gone up if hks were to make another car like that in a r34 format it would be probably twice as powerfully. Everything has its prime year...and it had passed :D

In the simpsons there was a electronic toliet, do they have them in japan?

If you mean electronic as in: heated seat, remote control (like... a DVD remote!) bidet, air drying, flush, motorized seat open/close and am/fm radio contrlos... then, yes.

:D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...