Jump to content
SAU Community

Recommended Posts

  • Replies 1k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Hey when are are people going to meet up with there skylines/imports again, I'm keen to come along it would be good to see some clean cars in this town again. Plus I need some better photos of my car and some promoted photos of a good turnout might get the ball rolling for bigger better things

p.s i reckon a good location to meet up would be under the new IGA at riverside gardens, nobody is ever there and its well lit.post-35424-0-89626900-1321260637_thumb.jpg

Was that the night you fuzed the clutch to flywheel Nigel?

I'll be keen to bring the GTR out once I finish spending all my money on carbon and finish the bottom end off.

may or may not have found the dash cluster surround in proper carbon :ph34r: now to get the sub meter in it too :ph34r:

Sure was, that sucked. Totally my fault too, a little embarrassing. I learnt a valuable lesson, don't let contaminants get in your bellhousing. But I did get to upgrade to a new clutch and it drives alot smoother.

Edited by Gads GTR

Eh, them's the breaks though mate. What clutch? from memory jim berry isnt it?

damehoo9090-img600x450-1172864921107-0718_img.jpg

damehoo9090-img600x450-1172864938100-0021_img.jpg

:ninja: :ninja: :ninja: :ninja: :ninja:

I got bored at work, and found it............................ waiting for email reply to pay for it >_<

and this strange_drive_jp-img600x400-12683684229w3bce84061.jpg

Something different from normal..... both should be here next week I think :O>_<

Edited by Force Fed

Yeah I did but it rained that day and I was just about the only one there. It was very slippery did 11.7 @124mph 2. Something 60ft. Was good for a thrash though, might wait till summer has come and gone before I head out there again.

Yeah I did but it rained that day and I was just about the only one there. It was very slippery did 11.7 @124mph 2. Something 60ft. Was good for a thrash though, might wait till summer has come and gone before I head out there again.

Nice work! Ripper MPH. 60foot is where the time was lost as you can see! Awesome!!!

Cal- awesome! If my clutch ends up being a push I'll swap to an NPC twin out of my mates 32 if he goes the 34gtr box

I kinda wish i went a twin plate. bought the clutch and then later on when i rebuilt the gearbox i bought a lightweight flywheel off NPC. ended up costing nearly as much as a twin plate would have but oh well haha

hahaha! big mouth track? good for about 600 ponies apparently.

I currently have the Exedy hyper multi twin in mine, but would much prefer an NPC unit :thumbsup:

Edited by Force Fed

Hmm, i called them yesterday, lady said she will give me a call back later in the day. Still waiting for the call a day later.

Tried to call them again today, no one is picking up the phone.

What is going on over there?

Anyone got other recommendations?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...