Jump to content
SAU Community

Burning Smell

TMW-R34

By TMW-R34,
in Engines & Forced Induction

 Share

Recommended Posts

TMW-R34 Collaborator

TMW-R34

Posted
Posted

Hi guys.

Was at a party last night and when i left, my mate told me to smoke it up a bit....so i did.

Revved till about 3-4 then dropped the clutch. Went up and hit the limiter and moved forward about 30 metres.

Didnt feel right so i reversed back and asked my mate if my wheels spun at all, and they didnt.

Got a rank smell in the car which was there for about 15 minutes. Wasnt tires or brakes, hadnt come across this smell before.

when i got home, i lifted the bonnet but there was no smell from there. Went around to the tires and the back passenger side stunk of this smell.

Im not sure if its my clutch, as it was fully disengaged when i "tried" to smoke it up.

Any ideas what it is or what it could be?? Not sure if i should be worried. :down:

Thanks guys.

Link to comment
https://www.sau.com.au/forums/topic/308981-burning-smell/
Share on other sites
MrStabby Grand Master

MrStabby

Posted
Posted

Yep sounds like clutch. Dont be surprised if it starts to slip when you hit boost.

Im not sure if its my clutch, as it was fully disengaged when i "tried" to smoke it up.

Not sure what you mean but that, you engage the clutch to drive the rear wheels. Your problem will be that its slipping when engaged.

Link to comment
https://www.sau.com.au/forums/topic/308981-burning-smell/#findComment-5097467
Share on other sites
paulr33 Grand Master

paulr33

Posted
Posted

yeah stock clutch is pretty good for normal driving

as soon as you wind it up or get on the burnouts in 2nd gear / clutch dumps = dont even bother

go for a single plate heavy duty

should be sub $1200 fitted and supplied

Link to comment
https://www.sau.com.au/forums/topic/308981-burning-smell/#findComment-5097498
Share on other sites
The Mafia Grand Master

The Mafia

Posted
Posted (edited)

lol. Your clutch is rooted.

Do you have a Vent to atmosphere BOV? That could also be the problem. Put the factory plumback on, and it will help. Puts less load on the clutch.

Edited by The Mafia
Link to comment
https://www.sau.com.au/forums/topic/308981-burning-smell/#findComment-5097510
Share on other sites
Finchy33 Enthusiast

Finchy33

Posted
Posted (edited)

Dump it harder...

More rev's and side step it, if your fairly violent with it, it'll break the initial traction and not really have time to slip.

Unless your running semis or something special :down:

Also, don't sit on the brake and dump it. Drop it, get it spinning and then apply as little brake as possible for desired effect.

Edited by Finchy33
Link to comment
https://www.sau.com.au/forums/topic/308981-burning-smell/#findComment-5097633
Share on other sites
Aberax Grand Master

Aberax

Posted
Posted

Lol, i did something like this too. Was trying to see some stats from a mates iPhone Dyno program. Revved it to 4-5k RPM, let the clutch out, wheels spun a bit, caught and then no power with the yummy burning clutch smell. Around 260rwkw, with stock clutch - i think its stock anyway, shall find out next week.

Link to comment
https://www.sau.com.au/forums/topic/308981-burning-smell/#findComment-5097659
Share on other sites
TMW-R34 Collaborator

TMW-R34

Posted
  • Author
Posted
lol. Your clutch is rooted.

Do you have a Vent to atmosphere BOV? That could also be the problem. Put the factory plumback on, and it will help. Puts less load on the clutch.

Yeah the stock blow off valve is on.

Link to comment
https://www.sau.com.au/forums/topic/308981-burning-smell/#findComment-5097710
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • TurboTapin
      new 1.5 LSD issues/concerns

      By TurboTapin · Posted

      My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • MBS206
      NC MX5

      By MBS206 · Posted

      Bunnings would have just handed you your money back on that one!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...