Jump to content
SAU Community

Recommended Posts

Just put a hypergear atr28g4 ig on the stock manifold with vband dump with extra bung for a techegde wideband. I do suspect the dump is leaking alittle at the vband clamp. It sounds fine while idling. I can plug in a mates motec PLM in the tail end and check it.

check how hot the wideband cabling is getting. i had an issue once with my techedge unit giving lean values, turned out the wiring was suffering from heat soak. but this was only happening after about 10-15min of driving once everything had warmed up.

Wideband cable shouldn't be the problem it dosn't appear to be getting hot. I will check out an exhaust leak being the problem. Does anybody use exhaust joiner paste when connecting turbo and dump via vband?

  • 3 weeks later...

Yeah i did do the calibration, I might do it again. I did do 1 stupid thing tho i had the wideband sensor pluged into the exhaust for alittle while while i was first sorting the bugs in my new system, but it was not wired up. Would this kill the sensor?

So basically the calibration was done on a dirty sensor

  • 2 weeks later...

Calibration changed nothing. it wont be the sensor the cruize afr sit in the 14's perfectly fine any ideas?

I have checked for vacume leaks with a can of carbie cleaner and no change to idle.

Would a stuffed altinator cause the fuel pump\injectors to flow less? i did notice when i pluged in nistune that to voltage level is barely hitting 12v?

aslo sometime the wideband unit starts flickering to its heat cycle meaning not eough voltage to keep it hot

If the O2 sensor is working and the ECU is going into closed loop then look at the fueling, a blocked fuel filter will lean out mixtures as the fuel pressure in the rail will be lower.

Just out of interest does the techedge O2 sensor have a narrowband output signal?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
×
×
  • Create New...