Jump to content
SAU Community

Recommended Posts

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

rear tyres need replacing (they came with the cars original wheels, who knows how old they are) (understandable)

the cat got loose on one side and the gasket slid out so i am endangering the ozone (understandable)

rear p plate not shown have to stick it outside the window so as everyone knows im a p plater, not just the lucky people in front of me (understandable???)

rear break lights needs to be sufficiently bright (understandable)

and finally

the all mighty "H" pattern is not displayed, because in the rare occassion that i decide to shift from 5th and forcefully into reverse, i can look at the "H" pattern and say "oh yeah..."

im happy :)

i also got fined for the p plate and also something else i forgot, which in turn have both got a cash value fine and loss of 3 points, but because he said i dont seem like a hoonish driver (must of been the sandles, unkept hair, and listening to queens of the stone age), although i am driving a hoonish car (must of been the car?), and the new rules state any p plate would lose their lisence once they lose 5 points, he only gave me the smaller p plate fine so i only lost 3 points

nice fellow

oh no doxx

the RWC is HARDER to get now

they check everything inside out f ur car!!

not just wats on the list

the RWC guys are strict now

last time i got defected for

1. steering wheel(must be padded)

2. brake paddle(must have rubber)

3. BOV( must be stock)

4.Air filter( must be boxed)

and guess what....i have to put the car back to stock level and i need a stock exhaust sys or else they wont let me pass

they even check whehter i need new tyres

these are not on the list

basically they will check it more strict than the cops!!

thats why i am worried for ya:(

yes , when they are busy is usually the best time, i had my wifes car defected for rim size so i swapped the tyres over , got jetspeed to give me the road worthy then took the ride to Vic roads in burwood ,,it was a busy day ,,i drove up ,,the inspector actually said to me "i thought u was here coz of the height of the car(my wifes car is basically sittin on the bump stops,has about a 48 mm clearance from the ground),,anyhow told him nope just the rim size,,he said ,"did i fix it ?",, i said ,"take a look",,he replied ,,"nahh rims look ok",,went inside got it cleared and see ya later.... and that was all inside 1 hour from when i got the defect.

Good Luck

Dave

You'll be ok Michael, I got done for blue lights in the front bar, steering wheel padding, BOV (cos it had a shiny one)! accelerator pedal must be a rubberised surface, (mind you under the metal impul cover it's hard plastic)! and he questioned the firmness of my suspension!! and the boost gauge was in my field of view!! :bs!: I took my car to a strict RWC place and he said well all of that is crap but take the shiny pedal cover off and your tires are borderline on the rear so fix that and replace your front brake pads. so on went some mags full set of brake pads and burwood vic roads processed it without looking at the car. the fine shat me though.

pffft u will be fine... u dont need a RWC to clear it... just need the things listed cleared.

u rapscalionish ruffian of a hoodlum!

driving around terrorising little old ladies with ur BLOWUP valve and turbocharger intercooler modulatoratron.

omg modulatoratron that's what I need! muahhaha

doxxeh where was this? coz I saw a burgandy r33 pulled over by a cop on high st today.

That P plate rule shits me, I had to take off my beautiful spider n replace it with a stock square POS P plate.

I need to change the tyres on my car too... the back ones have like 30% tread on em.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
×
×
  • Create New...