Jump to content
SAU Community

Will This Fit My R34?

noely1

By noely1,
in Engines & Forced Induction

 Share

Recommended Posts

noely1 Community Regular

noely1

Posted
Posted

will this fit my N/A r34 sedan??

http://cgi.ebay.com.au/WALBRO-FUEL-PUMP-Ni...=item23059f8795

also would 550cc injectors work well??

will the injectors that are labeled as "turbo" ones fit my n/a??

i know sfa about this sort of this so any info would be great!!!

cheers

Link to comment
https://www.sau.com.au/forums/topic/310055-will-this-fit-my-r34/
Share on other sites
PSI-FED Collaborator

PSI-FED

Posted
Posted (edited)
why do you want 550cc injectors for your NA? do you have an aftermarket ECU to run them?

and that wlabro pump looks too cheap to be genuine

lol took the words right out of my mouth.

Edited by PSI-FED
mad082 Grand Master

mad082

Posted
Posted

may i ask why you want to upgrade them? is the old pump failing? if not then don't bother. neither a bigger fuel pump nor injectors will give you a power increase. unless you have a hell of a lot of work done (such as having a turbo fitted) then there is no need as you won't even be close to maxing out the stock ones.

N-DAWG Mentor

N-DAWG

Posted
Posted

Does seem a bit cheap for a Walbro. A Walbro GSS342 should be a direct replacement (done it on my R34 GT for the turbo conversion) but as mentioned already, why do you need bigger pump and injectors?

GTT Injectors are a straight swap on an RB25DE NEO. iirc they are around 370cc? which is enough for me to run a turbo at around 10-12PSI on 10:1 CR. Unless your looking to rebuild your engine, put on a big turbo, one that would even require ditching the factory AFM... you're not going to need those size injectors and even then a Walbro GSS342 is good for 500HP (or is it 550)? nuff said though, spend the money elsewhere unless this is part of a major upgrade :)

noely1 Community Regular

noely1

Posted
  • Author
Posted

well im thinking of getting an APEXI fc +hand controller for my car... thats the reasoning behind it..

also anyone know who/where i can source one of these apparently they have been discontinued for the ER34's ?

N-DAWG Mentor

N-DAWG

Posted
Posted

Apexi Power FC should be fine as the car is manual and no longer needs the auto shift logic, and your replacing the ECU, not running a piggy back.

What are your long-term plans with the car? You would at least want to be working on the internals, upgraded camshafts, port polish, raise compression etc... to really take advantage of 550CC Injectors, bigger pump and a PowerFC... The cost of the PowerFC + Tuning = not worth it unless your at least fitting a snail

N-DAWG Mentor

N-DAWG

Posted
Posted

In that case buy your parts, but wait till your ready for it all to be put together before you start playing around with ECU's injectors and pumps. Only because it's unnecessary costs in labour and tuning, only to be retuned on the turbo conversion.

So to answer your question, a Walbro GSS342 is a direct replacement fuel pump, and R34 GTT Injectors will be a direct replacement, and will be plenty unless you want to go all out rebuilding your engine for higher horse power. Unless your able to get R34 550CC injectors at a really good price that's hard to pass up, then go for it, otherwise just stick with good 2nd hand GTT Injectors and you should be fine :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...