Jump to content
SAU Community

Recommended Posts

hey guys im new to this.........

i have a Nissan skyline 4door it came standard as a rb25de auto since then i have made it manual with a rb20de gearbox and just put a standard clutch in...

any way just wondering if you could tell me how to to put a turbo kit on it and eveything i would need to make it happen just going to start off with standard parts like standard 25det manifold etc but really need to no everything to get it running ...

and will i need a new gear box or will this last a while and will the clutch last a while as its brand new...???

need handy tips thank guys and girls =)

Link to comment
https://www.sau.com.au/forums/topic/311616-rb25det/
Share on other sites

You will need from an RB25DET...

Turbo preferably with water an oil lines

Air intake.

Exhaust manifold, to fit the turbo on.

Dump-pipe & Front pipe, full 3" exhaust system.

Fuel Pump (GTS-T one or better, plenty of high-flowing cheap ones out there, walbro etc)

Injectors (stock GTS-T ones or better)

Intercooler and piping (stock or custom)

Alloy cross-pipe with BOV (stock of custom)

ECU

Alter / lower your compression ratio, unless you are running a very low boost level.

You might want to run with a RB25DET gear box and RB25 rear Diff.

Stock RB25DET clutch or aftermarket single heavy duty.

With the turbo on, you car will go faster, you better at least upgrade your brake pads of get R33 GTS-T calipers / disks... Unless they are the same size.

Get wider / bigger wheels to give you more traction.

Upgrade your suspension.

Link to comment
https://www.sau.com.au/forums/topic/311616-rb25det/#findComment-5129661
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...