Jump to content
SAU Community

Recommended Posts

R32 Skyline Club are having their Third cruise!

This will be a Morning Run, The destination will be Pinjarra Bakery, for those who have not been they make unreal pies & sausage rolls! They shut at 2pm hense the early start. The Cruise will not be a hwy run, its more of a forrest drive eventually getting to Pinjarra.

Place: Midland Central - Clayton Street, Midland. Out the front of JB Hi Fi.

Time: Sunday 28th March 2010 - Meet at 8:30am for 9am leave

Bring a tank of fuel, I cant stress this enough, we will go past a couple of fuel stops but we are not stopping at any.

The Cruise is intended for owners of R32 Skylines,

however I am not going to tell you to leave if you bring a different model of Skyline, but Skylines only please.

Dont expect to come to a race, the club prides itself with just enjoying coming out and just being able to drive.

See you there!

Link to comment
https://www.sau.com.au/forums/topic/311792-28th-march-r32-skyline-club-cruise/
Share on other sites

i should be able to make this as long its a skyline run my 32 is back on the road after my last cruzz and a meeting with a commodore up my ass but sound good and the bakery is GOOD

That's my birthday :down:

Though I do drive a R33 GTR, I did notice you won't tell me to leave, but I'd feel stink if I was the only tool in a 33 at a 32 club cruise

It's alright dude, I'll be there in my StagBus as the 32 is still without an engine :huh:

hey buba come with us bro if u want its up to you

and i just got that 30 blok yeah :blink:

Naice!

I'm hoping to have the CB installed in teh StagBus by the weekend (programming cable just rocked up :P) and *hopefully* some new front brakes! so I'll be keen to give them a workout ;)

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...