Jump to content
SAU Community

Recommended Posts

Well I got the usual foggy headlights that most series 1 R33's get and it now looks very noticable.

Pulling the headlamps out looks like a big job, I have washer bottle, cold airbox etc all in the way.

Whats the best way to clean them and stop it from happening again ?

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/311860-foggy-headlights-on-r33/
Share on other sites

cleaning them up is easy . polish it with anything . everyone will tell you anyhting from jif to tooth paste . meguairs do a plastic polish called plastx . it works well .

nothing will stop them turning yellow again tho .

cleaning them up is easy . polish it with anything . everyone will tell you anyhting from jif to tooth paste . meguairs do a plastic polish called plastx . it works well .

nothing will stop them turning yellow again tho .

Do you have to pull the whole light out, or can you crack off the lense cover ?

cheers

cleaning them up is easy . polish it with anything . everyone will tell you anyhting from jif to tooth paste . meguairs do a plastic polish called plastx . it works well .

nothing will stop them turning yellow again tho .

How quickly do they discolour again? Is it annoyingly soon after polishing, or do they stay clear for a useful while?

should last at least 12 months before they go cloudy again, but will take a few years for them to get the real ugly yellow

that's interesting...

I thought it was simply moisture on the inside surface of the plastic.

So the clouding must be caused by UV exposure.

Also,my car is garaged and has only been in rain twice in 6 months, and the fogginess is getting worse.

Thanks for the tips, I'll give it a go.

if it is a general cloudyness and discolouration then yes it is caused by UV. if it is just foggy and you can actually see water droplets inside then you have a leak and it is caused by moisture. post up a picture of your light so i can have a look.

I find Brasso works wonders (also awesome removing scratches from DVDs) - just don't get it on your paintwork!

that's why i went with the scratch-x. it is actually a product designed for use on paint so it doesn't matter if it splatters or anything like that. i would just put the woolen buffing bad on the drill, put some scratch-x on the pad, smear it round on the light so it didn't just fly off, then pull the trigger on the drill. took about 5 or 6 seconds per light of actual buffing to get them clear. it would actually take me longer to get all the gear out

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lamb roast on Saturday will be different 🥲
    • They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...