Jump to content
SAU Community

Recommended Posts

ok i bought a r32 cheap, obiously there was a reason why an this im guessing is it,

its a r32 with high mount turbo bla bla bla

what seems to be happening is the oil is getting into the coolant somewhere, the actual engine oil doesnt get mixed it stays clear but the coolant is milky as fark, the gauge doesnt work in the car but it is overheating an emptying the radiator fast,

soo im guessing headgasket??? a oil chamber is leaking into coolant chamber?? but why doesnt the oil galerys get coolant in them ???

the guy i bought it off had engine oil in a coolant container ? is it possible he topped up radiator with the engine oil an thats why it keeps boiling quick ??

the car has no boost at all im getin a flat 0 on the gauge with minimal power

help someone out there!!!!!!!!

Link to comment
https://www.sau.com.au/forums/topic/312666-rb20-problem-need-quick-solution/
Share on other sites

maybe get a compression check, if its the head gasket thats gone as soon as it will try to boost it will just be leaking the boost out of the gasket, hence no boost, and you would have to be really stupid to put oil in the radiator,

ther may not be coolant in the oil because its more combustion gases that are getting into the coolant,

when ur car has been sitting over night does it turn over slowly for the first crank, if it does it could be coolant leaking back into the cylinder, but twhen its running the combustion is pushes into the coolant.

well i fully flushed out all the oil in the coolant, i rang the previous owner n he did say he put the "coolant" (actually oil) into the overflow bottle, i now have the other problems to look at which are

no boost max im getting on the gauge is 0 lol

smoke coming out of the catch can filter but its not even connected right ( is a line ment to go to sump? i only got to coming off top cover)

small amount of white smoke coming from exhaust on start up an rough idle on start up??

we can rule out the head,

i drove the car for over 1hr today

coolant remained same level no mixture of oil n water in ether motor or ratiator

i figured out why its not coming on boost lol im not reving it high enough!! DUHH lol over 5000rpm it starts up (i dont thrash my cars much)

only problem remaining is white smoke on start up??

there should be boost well before 5 grand unless u have a mammoth turbo

a standard 32 should start spooling at probs about 2-2.5 grand under load and have full boost by 3.5-4

there should be boost well before 5 grand unless u have a mammoth turbo

a standard 32 should start spooling at probs about 2-2.5 grand under load and have full boost by 3.5-4

He did say it had a high mount.. and full boost on a stock RB20 with stock turbo by 3500rpm?? That's when the 25 turbo on my RB20 was making 12psi.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
×
×
  • Create New...