Jump to content
SAU Community

Recommended Posts

ok i bought a r32 cheap, obiously there was a reason why an this im guessing is it,

its a r32 with high mount turbo bla bla bla

what seems to be happening is the oil is getting into the coolant somewhere, the actual engine oil doesnt get mixed it stays clear but the coolant is milky as fark, the gauge doesnt work in the car but it is overheating an emptying the radiator fast,

soo im guessing headgasket??? a oil chamber is leaking into coolant chamber?? but why doesnt the oil galerys get coolant in them ???

the guy i bought it off had engine oil in a coolant container ? is it possible he topped up radiator with the engine oil an thats why it keeps boiling quick ??

the car has no boost at all im getin a flat 0 on the gauge with minimal power

help someone out there!!!!!!!!

Link to comment
https://www.sau.com.au/forums/topic/312666-rb20-problem-need-quick-solution/
Share on other sites

maybe get a compression check, if its the head gasket thats gone as soon as it will try to boost it will just be leaking the boost out of the gasket, hence no boost, and you would have to be really stupid to put oil in the radiator,

ther may not be coolant in the oil because its more combustion gases that are getting into the coolant,

when ur car has been sitting over night does it turn over slowly for the first crank, if it does it could be coolant leaking back into the cylinder, but twhen its running the combustion is pushes into the coolant.

well i fully flushed out all the oil in the coolant, i rang the previous owner n he did say he put the "coolant" (actually oil) into the overflow bottle, i now have the other problems to look at which are

no boost max im getting on the gauge is 0 lol

smoke coming out of the catch can filter but its not even connected right ( is a line ment to go to sump? i only got to coming off top cover)

small amount of white smoke coming from exhaust on start up an rough idle on start up??

we can rule out the head,

i drove the car for over 1hr today

coolant remained same level no mixture of oil n water in ether motor or ratiator

i figured out why its not coming on boost lol im not reving it high enough!! DUHH lol over 5000rpm it starts up (i dont thrash my cars much)

only problem remaining is white smoke on start up??

there should be boost well before 5 grand unless u have a mammoth turbo

a standard 32 should start spooling at probs about 2-2.5 grand under load and have full boost by 3.5-4

there should be boost well before 5 grand unless u have a mammoth turbo

a standard 32 should start spooling at probs about 2-2.5 grand under load and have full boost by 3.5-4

He did say it had a high mount.. and full boost on a stock RB20 with stock turbo by 3500rpm?? That's when the 25 turbo on my RB20 was making 12psi.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello, just just bought an 1999 enr34 with a stock rb25neo and I'm looking to upgrade the engine to 500whp I know some basic things but wondering if there are things I'll need to do to upgrade the stock block and all the bits and pieces to achieve this.
    • Thanks everyone for the replies and suggestions. Got the seats out (hoping I could find some existing grommets but no such luck). By tapping and measuring etc. I could figure out where I could drill through if needed. But first I borrowed an inspection camera and managed to go through factory holes in the chassis rail and could see that the captive nut was holding steady which is why it could retighten. So it was indeed a stripped section of thread, so I applied downforce by levering the bolt head with a screwdriver and went slowly back and forth until it came out. Camera helped a lot cos I could monitor that the captive nut was holding tight. Now I just have one very seized main subframe nut to tackle 馃槄
    • BOVs do have a purpose, if you ever log pressure before and after the throttle body, you will see a spike pre throttle on lift off from a WOT condition. Enough to bend throttle blades / damage e-throttle motors or simple assist in blowing off cooler pipes. FWIW, the above on really applies to those running at least 2 bar of boost. OP shouldn't have an issue, on the other hand, here are some videos of my shit box over a decade ago with some succulent dose with the airbox on and off. That shit box is unrecognisable these days 馃珷    
    • I've tried all different combinations of BOVs/ no BOV and stock bypass valves over the years, on gear changes the stock bypass valve seems to get the car back on boost quicker because in part the turbos wheel speed isn't being slowed down by reversion, although they have issues holding boost much over the stock setting. Most aftermarket BOVs you can adjust the spring, tighter will make it open later and close sooner, but in my experience it'll cause a bit of flutter at low load/rpm anyway. I've also got some input into this whole no bov causing turbo wear, never had an issue on any on my turbos HOWEVER, I got my R33 GTST with 200k kms on it, with from what I can see still has the original turbo, no lateral shaft play but has about 4-5mm of play in and out which to me seems like a worn thrust bearing from years (100-150k kms?) of turbo flutter running no bov, so maybe there is some truth to it in the long run. But that'll never stop me loving the Stutututu while I have the car.   OP just wants to know if he can run a atmo vented BOV with no major issues and the answer is YES, plenty of people do it, there's no harm in installing it and seeing how it runs before spending $$$ on an aftermarket ecu, last time I bought a Nistune it was $2400 for install and a tune , unsure of todays prices but you get me. Crazy money to spend just to fix the minor inconvenience of stalling that can be overcome by letting the revs come down to near idle before putting the clutch in or a little bit of throttle to avoid it. You're better off leaving the ecu and tune for after a bigger turbo/injectors have been installed to take full advantage of the tune and get your moneys worth.   Let OP have his Whoosh sound without trying to break his bank haha
    • I see you missed the rest of the conversation where they have benefits, but nothing to do with avoiding breaking turbos, which is what the aftermarket BOV made all the fan boys, tuners, and modders believe was the only purpose for them...
  • Create New...