Jump to content
SAU Community

Recommended Posts

95 series 1 1/2 R33 complete interior parts no front or rear seats already sold.

R33 rear cradle no diff and breaks

R33 powersteering rack & hubs

R33 Bonnet

R33 series 2 Boot with Wing, rear bar & rear lights

R33 series 1 headlights excellent condition

S15 front 5 stud hubs with breaks off non turbo s15

R33 rear 5 stud hubs no breaks

Series 2 drivers seat no rips or tears

ALL MUST GO PM OR CALL FOR what u need and for PRICE OR MAKE OFFER

0433329781

Link to comment
https://www.sau.com.au/forums/topic/313454-wrecking-r33/
Share on other sites

95 series 1 1/2 R33 complete interior parts no front or rear seats already sold.

R33 rear cradle no diff and breaks

R33 powersteering rack & hubs

R33 Bonnet

R33 series 2 Boot with Wing, rear bar & rear lights

R33 series 1 headlights excellent condition

S15 front 5 stud hubs with breaks off non turbo s15

R33 rear 5 stud hubs no breaks

Series 2 drivers seat no rips or tears

ALL MUST GO PM OR CALL FOR what u need and for PRICE OR MAKE OFFER

0433329781

Link to comment
https://www.sau.com.au/forums/topic/313454-wrecking-r33/#findComment-5151072
Share on other sites

is that the bit thats rapped around the indicater stalk

its under that, its also is were the bonnet opening handle is, its a long colum, also there is a part there were you can move your steering wheel up and down. about 120cm, just guessing the length, but would be close.. ill find a pic if it helps a bit. im after one with no broken parts :banana:.. thanx

Link to comment
https://www.sau.com.au/forums/topic/313454-wrecking-r33/#findComment-5151119
Share on other sites

its under that, its also is were the bonnet opening handle is, its a long colum, also there is a part there were you can move your steering wheel up and down. about 120cm, just guessing the length, but would be close.. ill find a pic if it helps a bit. im after one with no broken parts :thumbsup: .. thanx
is it the one where the fuse box is if so i sold it
Link to comment
https://www.sau.com.au/forums/topic/313454-wrecking-r33/#findComment-5151786
Share on other sites

  • 2 weeks later...


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...