Jump to content
SAU Community

Front Diff Problem

Mr.Massive
 Share

Recommended Posts

Mr.Massive Community Regular

Mr.Massive

Posted
Posted

Hey Guys,

Ive just replaced the front diff in my stagea engine to the gts4. I had a mate come round to do it who was a mechanic and i am just concerned about the yoke (part where the front shaft connects and spins the diff centre). It doesn't seem to be moving at all even with a few jolts with a wrench. The hubs spin when i turn them however the yoke doesn't, which tells me the spider gears are ok. Im thinking it just needs alot of pressure on it which is hard to do at the moment due to my car being on jack stands. Should it be ok to connect the front shaft to it and hopefully it will turn as it seems to be stuck?

Any thoughts guys? Cheers

Link to comment
https://www.sau.com.au/forums/topic/313807-front-diff-problem/
Share on other sites
Luciano Veteran

Luciano

Posted
Posted

posting on behalf of Mr.Massive

did he rebuild it or just replace it with a 2nd hand unit?

he replaced it with original front diff centre out of the gts4 (rb25de)

Did your mate also swap over the pinion gear?

this we're not sure of. this is potentially the gear causing no spin. I'm thinking that the mechanic may have presumed that this gear in question was an identical item

could this one be the problem?

Get someone to hold one wheel for you while you spin the other- if the diff is stuck then you won't be able to turn it

can give this a try

Another thing - did you also swap the rear diff. The car will have serious problems if the front and rear diff ratios don't match.

no. as per first quote, the front diff was replaced so it will match the rear

Luciano Veteran

Luciano

Posted
Posted
Did your mate also swap over the pinion gear?

just got confirmed this part was definitely changed.

would you guys think it'll be safe to bolt her all up and take it for a drive? ive got a feeling it just needs a bit of a good forced turn from the gearbox to come unstuck. Just dont want to break anything!

Deano 1 Mentor

Deano 1

Posted
Posted

when i re-shimed to diff in my old silvia drift car, it was pritty stiff once all bolted back togethor, as i tightened the 4bolts that hold the centre in the housing i had to keep rotating the diff using the tailshaft flage and a socket on the bolt on the inside of it, but when it was all tight and full of oil it was still fairly stiff to turn, eg= u needed a tool to turn it, i bolted it in the car and went for a run up the street that put it back on the hoist and it free'd up,

so depending how hard it is the turn atm will matter if u drive it or not, can u turn it round with a tool?? or is it just fullly locked up?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      R32 GTST - 600KW+ RB28/CD009 Build

      By Dose Pipe Sutututu · Posted

      LOL.... a good amount of people (not all) on that continent seem to know everything and like to measure things in bananas, football fields, statue of liberties instead of the metric system lol.
    • dawhitehonky
      M35 Aftermarket Fuel Pump

      By dawhitehonky · Posted

      I assume the modules are similar enough, so if you've had no issues I don't see why I would. I have tried to find a wiring diagram for the FPCM / fuel pump circuit, but I can't find it anywhere. Otherwise, I would just do some wire cutting and joining at the FPCM and give the 12 V supplied to the FPCM directly to the pump instead. If you know anyone that could help with wiring diagrams, I'd be very happy  
    • GTSBoy
      M35 Aftermarket Fuel Pump

      By GTSBoy · Posted

      If it dies, then bypass. The task isn't difficult. I have one running on a standard R32 FPCM. That's after nearly 20 years of it running an 040, which pull substantially more current than the Walbro. They're not the same module, but I'd hope it indicates that the R33 one should be man enough for the job. I think people kill them when putting proper sized pumps on them, not these little toy pumps we're talking about here.
    • GTSBoy
      Rapid-fire squeaking/creaking from rear suspension

      By GTSBoy · Posted

      Silicone spray won't hurt anything. And if it does, that's an opportunity to put some solid steel spherical bushings in, so you can really learn what suspension noise sounds like, If you're going to try it, just spray one bush at a time, so you can work out which one is actually noisy. My best guess is that if the noise started only since putting the coilovers in, then it is just noise being transmitted up through the top mounts of the struts, and not necessarily "new" noise from bushes. But it's almost impossible to know.
    • GTSBoy
      Jacks that fit under GTR lips that can reach the subframe?

      By GTSBoy · Posted

      Are you saying the 34 is SUV height, and not that we're talking about an SUV here? (because if we're talking about an SUV, you don't fix them. You just replace them when something breaks. Not worth establishing sufficient emotional connection with an SUV to warrant doing any work on one). I wouldn't jack my car up on a short little loop of 10mm steel rod poking out through a hole in the bumper bar, front or rear end. I realise that we're probably not talking about that type of loop at the front, being the one under/behind the bar on a Skyline.... but even for that one, trying to jack up on what amounts to a thin piece of steel, designed purely for withstanding a horizontal tension force, not a vertical compressive force (and so would be prone to buckling/crushing) and, my most particular bitch about it - located RIGHT AT THE EXTREME FRONT OF THE CAR, applying a load up through the radiator support panel, etc, with almost the entire mass of the car cantilevered between there and the rear wheels? Nope. Not doing that. Not on the regular. That structure out there in front of the front crossmember is not designed to carry load in the vertical direction. Not really designed to carry any load at all, really. The chassis rail that the tow point is connected to would be fine loaded in tension, as per towing. Not intended to carry the mass of the whole car, especially loaded all on one rail, with twisting and all sorts of shitty load distribution going on. No, I will happily drive up on some pieces of wood, thanks. That can only happen on driven wheels, and they are at the other end of the car, and this problem does not exist at that end of the car. And even then, I have been known to drive up on at least 1x piece of 2x8 each side at the rear, simply to reduce the amount of jack pumping necessary to get the car up high enough for the jack stands. What really really shits me about Skylines is the lack of decent places for chassis stands at either end of the car. You'd think they'd be designed into the crossmembers.
×
×
  • Create New...