Jump to content
SAU Community

Recommended Posts

Hi all, just recently stuffed the rear turbo on my GTR. Sounds like a helicopter now as soon as any boost is raised. I've rung a few Jap import places and most have said they're pretty hard things to find.

Anyone been in this situation before and what did you do? I'm thinking a new turbo setup might be the go but money's tight at the moment due to building a house. Any suggestions would be appreciated! :P

Link to comment
https://www.sau.com.au/forums/topic/31445-blown-turbo-on-gtr-any-advice/
Share on other sites

This happened to me back in September. If it happened a week ealier, I couldve sold you my one working stock turbo, but its already been sold, sorry :P

From when I was pricing around I was quoted around the $800 mark per turbo to just rebuild and steel wheel the turbos (not highflow and no ball bearing). Rebuild, steel wheel and ball bearing to N1 specs was $2200 per turbo at GCG (ouch!).

In the end I got a set of second hand HKS GT2530's that were rebuilt in Japan by HKS (not rebuilt to Garret specs). Id say to save some pennys and either go replacements like the HKS ones, or rebuild + high flow + bb your standard ones.

Thanks heaps guys. Clint32, once I get the turbos off and get them sussed out I'll PM you.

We're organising a Group buy of Garret Turbos.. the prices are awesome, & haven't yet seen them cheaper anywhere else. Let me know, as we're trying to have the order put in by late jan, early feb.

here's the link, http://www.skylinesaustralia.com/forums/sh...ead.php?t=30086

I had been running 15PSI since I got the car, occasionally putting it up to 16PSI for the drags and cruises etc.

New years eve we went for a strap on an island with long straights on a private road getting it up to the 240km/h mark in fourth gear. Everything was fine until I slowed down then went to accelerate and I just thought what the f*ck is that noise....... worst thing I've ever heard. :(

We had to drive home about 100km at 50km/h (otherwise boost would cause that horrible helicopter sound), was quite strange having people overtake you like you don't know how to drive a GT-R or something. ;)

BTW, my car's only just done 70,000km now. And I'm pretty sure they're original km's coz everything's immaculate inside (and out). So don't be tempted to wind that boost up!

You were lucky that the turbo lasted as long as it did - stock R32 GTR turbos should not be run any higher than 14psi from what I have been told.

You can run higher boost on a stock motor (presently running around 20psi) but depending on the condition of the motor & quality of your tune it is also getting into the danger zone.

Thanks for the advice guys, I'm actually thinking of going to a single turbo depending on cost. I'd love 2530's or T51's but if I can get good response from a single then it's going to save me money in hardware.

Anyone converted from twin to single? Would you recommend it?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...