Jump to content
SAU Community

Got Egged!

SiNNO

By SiNNO,
in New South Wales

 Share

Recommended Posts

Lepperfish Mentor

Lepperfish

Posted
Posted

I got egged once. While driving, it was on halloween night a couple of years ago. At first glance it appeared to have caused no damage but after closer examination the next day it had cracked up the black plastic on the door where the window slides up and down. Little f**ks. I did a lap of the block, parked and jumped out with a mate. There was 5 of these little f**ks, all about 16. They scampered when they saw us coming but managed to get ahold of one of them. Lets just say these pricks won't ever through eggs again after seeing their mate stumble down the road to where they were hiding, lol....

Touge Kyousou Experienced

Touge Kyousou

Posted
Posted
I got egged once. While driving, it was on halloween night a couple of years ago. At first glance it appeared to have caused no damage but after closer examination the next day it had cracked up the black plastic on the door where the window slides up and down. Little f**ks. I did a lap of the block, parked and jumped out with a mate. There was 5 of these little f**ks, all about 16. They scampered when they saw us coming but managed to get ahold of one of them. Lets just say these pricks won't ever through eggs again after seeing their mate stumble down the road to where they were hiding, lol....

Lucky bastard...i'd love to get my hands on some egging douche head. My old mps3 got done once, bad paint chip and my current v35 also got done once. Cockmunches

GTR-N1 Grand Master

GTR-N1

Posted
Posted

What we feel like doing - and what we end up doing...

could be two different things??? :( > this has been bounced from VIC sect'n

http://www.heraldsun.com.au/news/enraged-c...o-1225861089441 :)

Perhaps he'd like me to furnish a character report? :)

Humbla Grand Master

Humbla

Posted
Posted
What we feel like doing - and what we end up doing...

could be two different things??? :( > this has been bounced from VIC sect'n

http://www.heraldsun.com.au/news/enraged-c...o-1225861089441 :)

Perhaps he'd like me to furnish a character report? :)

I hate peeps that do this,seem to have too much time on there hands,b.t.w. Terry you have pm.

Kujotk Grand Master

Kujotk

Posted
Posted
Not really. When you step back and look at the rest of the world. We have it the best.

I wouldn't call it the best, Its right up there but we do not have it the best.

PR34CH Mentor

PR34CH

Posted
Posted
What we feel like doing - and what we end up doing...

could be two different things??? :P > this has been bounced from VIC sect'n

http://www.heraldsun.com.au/news/enraged-c...o-1225861089441 :P

Perhaps he'd like me to furnish a character report? :P

LOL Owned .. where do you find these Terry.. some one has too much time on their hands!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...