Jump to content
SAU Community

Tomei Rb25 Ser.1 Poncams Specs Needed

Takoon

By Takoon,
in Engines & Forced Induction

 Share

Recommended Posts

Takoon Rookie

Takoon

Posted
Posted

Hello guys,

have these PONCAMS

http://www.nengun.com/tomei/pon-camshafts

Part Number: 143020 "ECR33 Series 1 (RB25DET) - Duration: IN,EX 256 Lift: IN,EX 8.5mm Skyline - R33 GTS-t S1 - ECR33"

and need the technical specifications to adjust them. Only found the duration, but not the opening and closing times as for example you can see here:

http://www.jdmlevin.com/files/CamshaftData...akeCamshaft.jpg

May anybody help me? I searched in the web, but without any results.

Thanks and best regards

vik

tridentt150v Grand Master

tridentt150v

Posted
Posted

Tomei poncams are a drop in replacement and have optimal timing standard. That is, you set them up with 0 degrees advance. You can try a degree or so, but I doubt you will see any improvement over zero - in fact you will more likely see a decrease in power and efficiency.

PM-R33 Grand Master

PM-R33

Posted
Posted (edited)

Same reason people upgrade camshafts in any vehicle, more duration and more lift over standard camshafts.

Procams are once again more lift and more duration over Poncams.

Edited by PM-R33
tridentt150v Grand Master

tridentt150v

Posted
Posted

Do a search, I remember reading a thread on here? that showed no difference in the top end, but a good mid range improvement of around 10-30kw depending on supporting mods. This is pretty much exactly where you need it IMO. Plus if your engine is breathing better it has to be more efficient.

jarrod83 Community Regular

jarrod83

Posted
Posted

did you lose any boost response? from the dynos i have seen between different cars i thought the cams lost down end response without any descent gains in the top end.. i'll have another search for that thread, i was searching 256 dynos before but didnt get anything descent.. can you remember any keywords

Cheers

Jarrod

PM-R33 Grand Master

PM-R33

Posted
Posted (edited)

Here's my old thread:

http://www.skylinesaustralia.com/forums/Dy...ns-t270208.html

As you can see no drops in power anywhere with the headwork. Obviously you have to consider I did a bit more than just the Poncams though.

Edited by PM-R33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Cas issue

      By GTSBoy · Posted

      The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Duncan
      RB26DETT Sketchy boost mod?

      By Duncan · Posted

      Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • nash47
      Cas issue

      By nash47 · Posted

      Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • nxh
      R34 4 door side skirt identification

      By nxh · Posted

      Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...